Bedienungsanleitung Technics SUR1EB (Seite 20 von 240) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Finnisch)

622409

Zoom out

Zoom in

Vorherige Seite

1/240

Nächste Seite

Sound adjustment

The following sound effects can be added to the audio output.

Re-mastering expands the playback band and achieves a

higher bit depth to reproduce natural and expansive sound

close to original music.

≥ The factory default is “Off”.

Press [RE-MASTER] to select “On”/“Off”.

This unit can transmit input signals without passing them

through its digital signal processor (DSP), via the shortest

possible path. This enables faithful and high quality

reproduction of original sound.

≥ The factory default is “Off”.

Press [DIRECT] to select “On”/“Off”.

You can set an upper limit on the output sampling frequency

range. Please note that the range that can be processed

differs depending on the amplifier or D/A converter. For

details, refer to the operating instructions of the connected

device.

≥ The factory default is “32kHz-192kHz”.

Preparation

≥Set “Digital Output” to “On”.

1 Press [SETUP].

2 Press [3, 4] repeatedly to select “D.Output

fs” and then press [OK].

3 Press [3, 4] to select an item and then

press [OK].

≥You can select a sampling frequency of 96 kHz or

192 kHz.

If audio distortion occurs when using the analogue audio

input terminals, set the attenuator to “On”.

≥ The factory default is “Off”.

1 Press [SETUP].

2 Press [3, 4] repeatedly to select

“Attenuator” and then press [OK].

3 Press [3, 4] to select “LINE1” or “LINE2”.

4 Press [2, 1] to select “On” and then press

[OK].

Disabling the audio output of unused terminals minimises

noise and allows playback in higher audio quality.

≥ The factory default is “On”.

1 Press [SETUP].

To disable the digital audio output:

Press [3, 4] repeatedly to select “Digital Output” and

then press [OK].

To disable the analogue audio output:

Press [3, 4] repeatedly to select “Analog Output” and

then press [OK].

To disable the system terminal output (SE-R1):

Press [3, 4] repeatedly to select “Digital Link” and then

press [OK].

2 Press [3, 4] to select “Off” and then press

[OK].

≥To enable the output again, select “On”.



≥ Depending on the music source that you play back, the applied

setting may be less effective.

≥ Depending on the music source that you play back, it may not be

possible to achieve the desired audio quality and sound field

effect. In such cases, turn off this function.

≥ Both Re-master and Direct mode cannot be set to “On”.

≥ When “Digital Output”, “Analog Output” and “Digital Link” are set to

“Off”, no sound will be output.

≥ When a headphone plug is connected, even if “Analog Output” is

set to “Off”, it is not possible to disable the analogue audio output.

≥ It may take some time to output audio when you have adjusted the

audio quality.

Listening to more natural-

sounding audio (Re-master)

Direct mode

Setting the sampling

frequency

Minimising audio distortion

Disabling audio output

(20)

SU-R1-SQT0463_EBEG_mst.book 20 ページ２０１５年６月１８日　木曜日　午前１１時５４分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Technics SUR1EB Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Technics SUR1EB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info