Bedienungsanleitung Technics SX-KN2400 (Seite 79 von 200) (Englisch)

536099

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

Part IV Sequencer

QQTG0692

Sequencer

Use the TEMPO/PROGRAM to adjust the

recording tempo.

• The tempo is shown on the display as

• If you wish to record the tempo setting and

tempo changes, store them in the control

(CTL) part, or use the step record to store

them in the rhythm (RHY) part.

Turn the metronome on or off as desired with

the ON/OFF button at the upper right of the

display.

• The metronome selection alternates between

ON and OFF each time the button is

pressed.

• When set to ON, the metronome volume set-

ting display is momentarily shown.

• The metronome sound is not recorded.

10.

Play the keyboard.

• Recording begins.

• You can also press the START/STOP button

to start the rhythm and begin recording.

• If the metronome is on, when you press the

START/STOP button, a two-measure count

plays, after which recording automatically

begins. In this case, the rhythm does not

start. Recording does not start until the two-

measure count is completed.

• The recording status is continuously updated

on the display:

MEASURE= indicates the current measure.

TIME SIG.= indicates the current time sig-

nature.

MEMORY= indicates the remaining mem-

ory (%) available for recording.

• If you wish to redo the recording, press the

REC STOP button and then record again. To

change the sounds and effects, etc. please

set them again.

• If you make a mistake in recording, you can

correct a specific portion of your perfor-

mance without having to redo the whole part.

(Refer to page 84.)

11.

When you have finished recording, press the

REC STOP button on the display, or turn off

the PROGRAM MENUS button.

• When the PROGRAM MENUS button is

turned off, the ending command (END) is

recorded. Note that, as long as the ending

command is not recorded, blank recording

continues even if you stop playing.

• The SEQUENCER PLAY button turns on.

Ⅲ

ⅢⅢ

Ⅲ

Multi-track recording

Use the following procedure to record one track

while listening to the track or tracks already

recorded.

Follow the procedure to record the first track,

and press the REC STOP button at the end of

the recording.

• The indication for the track just recorded

changes from “REC” to “PLAY”.

Turn on the “REC” indication for the track you

wish to record next, and select the sounds and

effects, etc.

Press the START/STOP button and begin

recording.

• Tracks for which “PLAY” is shown are played

back, and you can record in time with this.

• If you turn on the “REC” for the CONTROL

track and begin recording, the rhythm start will

not be recorded.

Press the REC STOP button at the end of the

recording.

Repeat steps 2 to 4 for other tracks, as

desired.

When multi-track recording is finished, turn off

the PROGRAM MENUS button.

• If you wish to store part settings that you mod-

ified after recording as beginning song data,

press the MIXER button and follow the PANEL

WRITE procedure. (Refer to page 83.)

09_Part IV.fm 79 ページ２００３年２月５日　水曜日　午後１時３４分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Technics SX-KN2400 Seite 79

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info