536100
86
Zoom out
Zoom in
Vorherige Seite
1/200
Nächste Seite
Part IV Sequencer
86
QQTG0692
Sequencer
Step Record
STEP RECORD is simply a method of making a tune by storing the sounds note-by-note on the display.
Instead of playing the keyboard directly as in the REALTIME RECORD mode, you can take your time to
input each single note. This is an especially effective method for storing complicated passages that are
difficult to play or when the exact timing of a part is critical.
Recording procedure
Record the keyboard performance and panel
changes.
1.
On the SEQ MENU display, use the SONG
SELECT
and
buttons to select the song
number. Then select RECORD & EDIT.
2.
On the RECORD & EDIT display, select STEP
RECORD.
The display changes to the PART SELECT
display.
3.
Use the balance buttons below the display to
specify the track for the part you are going to
record (only one track can be selected at a
time).
The display changes to the STEP RECORD
input display similar to the following.
If you selected the track to which the CHORD
part has been assigned, the display changes
to the STEP RECORD: CHORD display.
(Refer to page 88.)
If you selected the track to which the
RHYTHM part has been assigned, the display
changes to the STEP RECORD: RHYTHM
display. (Refer to page 90.)
If you selected the track to which the CON-
TROL part has been assigned, the display
changes to the STEP RECORD: CONTROL
display.
4.
Use the MEAS
and
buttons to select the
measure.
This step is not necessary if you are recording
from measure 1 of a blank track.
5.
Use the CURSOR
and
buttons to move
the cursor to the note position (dot) you are
going to store.
Each dot represents one-eighth of a quarter-
note (a thirty-second note).
When storing triplets, it may not be possible to
match the timing exactly with the 1/32-note
steps. However, if you select triplet-type notes
for the note length (LENGTH) in step 6 below,
the timing is automatically corrected.
6.
Use the left REC NOTE LENGTH
and
buttons to specify the note value. Select from
r
3
,
r
,
x
3
,
x
,
e
3
,
e
,
q
3
,
q
,
h
,
w
,
w
× 2 to 4. (A 3
denotes a triplet-type note.)
For note values other than these, use the cen-
ter REC NOTE LENGTH buttons to specify
the note value to be added to that which you
specified with the left buttons.
Example: To record a dotted quarter-note
(
q
.
)
q
+
e
7.
Use the right REC NOTE LENGTH
and
buttons to specify the actual length of the
produced sound for the desired legato or
staccato effect.
8.
Specify the pitch and velocity of the note by
playing the keyboard.
The dot on the display where the note is
stored changes to a
mark.
When recording chords, you can store multiple
notes at one position.
TENU (tenuto): Sound is produced for 95%
of the note length.
NORM (normal): 80%
STAC (staccato): 50%
CUTT (cutting): 25%
09_Part IV.fm 86 ペー ジ 2003年2月 5日 水曜日  午後1時34分
86

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Technics SX-KN2600 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info