Bedienungsanleitung Techno line WS6449 (Seite 11 von 62) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

801423

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

GB 3

 Once the Channel numbers on weather station and sensor are the same, proceed by opening the battery

cover at the back of your wireless sensor and insert 2 x AAA new alkaline batteries to the battery

compartment. Replace the battery cover.

 Your weather station will receive the data signal from the outdoor transmitter in a few seconds.

 Place your outdoor transmitter in a dry and shaded area once the weather station receives the data of this

sensor.

Note:

 If the weather station is used with 2 or 3 transmitters, press “CH” button shortly to display Channel 1,

Channel 2, Channel 3 or cyclic display.

 In cyclic display, the channel will be changed every 25 seconds in overview all channels in a short period of

time

Deleting sensors / clearing channels

 Press and hold the “CH” button for 3 seconds to clear the current channel to re-register

Display / Keys Details:

There are six function buttons:

DCF Reception icon with full signal strength will appear on screen if the reception of atomic time is

successful.

 In normal display mode, press this “-/RCC” button to start/stop time searching (DCF).

 The tower icon will show solid when the station has received the DCF signal.

 No tower icon displayed. The station was unable to receive a signal at this time.

Reposition the station for better signal reception and wait an overnight.

automatically receive Hours: Daily 1:00,2:00,3:00,4:00,5:00 DCF automatically receive, at any time once

received 3,4,5:00 no longer receive the same day

Only if the unit receives summer time, it will display the “DST” icon.

 If there is no signal or too much interference the receiver will only be on for 2 minutes.

 If the signal is good it may catch a signal in ABOUT 2-3 minutes.

 If the signal is marginal it will try to catch a signal for up to 10 minutes.

Manual Time Setting:

 Press and hold the “SET” button for 3 seconds in normal display mode to enter time setting mode.

 12Hr or 24Hr will flash. Press the “+” or “-“ button to select between the 12-hour or 24-hour time format.

Press the “SET” button to confirm and continue.

 The time zone will flash on the display. Press the “+” or “-“ button to set the desired time zone( setting

range is 0~ +12,0~ -12). Press the “SET” button to confirm and continue.

 The hour will flash. Press the “+” or “-“ button to select the hour. Press the “SET” button to confirm and

continue.

 The minutes will flash. Press the “+” or “-“ button to select the minutes. Press the “SET” button to

confirm and continue.

 The year will flash. Press the “+” or “-“ button to select the year. Press the “SET” button to confirm and

continue.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Techno line WS6449 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info