Bedienungsanleitung Techno line WS8016 (Seite 14 von 62) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch, Polnisch)

801527

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

EN6

 Press “ALARM” button can switch the display ALARM1 time or ALARM2 time, in the alarm1 or

alarm2 display mode, press the “UP” button to turn the alarm on or off.

 The alarm 1 or alarm 2 turn on, the “ ” or “ ”icon is displayed, the alarm 1 or alarm 2

function is open, The repeat of alarm icon at the same time is also displayed.

 The alarm 1 or alarm 2 turn off, the“ ” or “ ”icon disappears, the alarm 1 or alarm 2

function is close.

Notes:

 The alarm will sound for 2 minutes if you do not deactivate it by pressing any button. In this

case the alarm will be repeated automatically after 24 hours.

 Rising alarm sound (crescendo, duration: 2 minutes) changes the volume 4 times whilst the

alarm signal is heard.

Stop the alarm signal

 During the alarm sound, press any button to stop the alarm.

Snooze function:

 When the time is up to the alarm, touch “SNOOZE”, the alarm signal stops, and enter the

SNOOZE mode. After the snooze time is counted, the alarm will ring again.

 In snooze mode, press any button buttons or touch “SNOOZE” and hold for more than 2

seconds to exit the snooze mode.

Notes:

 When the snooze function is set to OFF, when the time is up to the alarm, touch the

“SNOOZE” character position does not have this snooze function.

Temperature & Humidity Detection:

 Temperature measuring range: -9.9°C (+14°F) ~ +50°C (+122°F), LL °C(°F) will displayed if

value lower than -9.9°C (+14°F), HH °C(°F) will displayed if value higher than +50°C (+122°F).

 Humidity measuring range: 20%RH ~ 95%RH, 19%RH will displayed if value lower than

20%RH, 96%RH will displayed if value higher than 95%RH.

°C or °F temperature display

 The temperature is displayed either in °C or °F. Briefly pressing the “°C/°F” button allows you

to switch between °C or °F.

Low battery:

 When the low voltage icon “ ” is displayed, you need to replace the battery.

Trouble shooting

If your clock displays irrelevant time or does not function properly, which maybe caused by electro-

static discharge or other interference, slide open the battery cover, take out the batteries and reinstall

them by observing the correct +/- polarity. Your unit will be reset to default settings and you need to

set it again.

Hereby, Technotrade declares that this product WS8016 is in compliance with the essential

requirements and other relevant provisions of Directive 2014/53/EU and ROHS 2011/65/EC. The

original EU declaration of conformity may be found at: www.technoline.de/doc/4029665080161

Environmental reception effects

The clock obtains the accurate time with wireless technology. Same as all wireless devices, the

reception is maybe affected by the following circumstances:

 long transmitting distance

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Techno line WS8016 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info