Bedienungsanleitung Technomax GMT vanaf 2009 (Seite 1 von 2) (Englisch)

622561

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Istr-trony-6 cod-eng GMT S2 Pag. 1

di 2

INSTRUCTION HANDBOOK FOR

ELECTRONIC DOUBLE CODE SAFES

Please read all of these instructions carefully before commencing using your

safe. Try all of these procedures with the door open first, until you are familiar with how the safe works

1. FEATURES

 High performance microprocessor.

 ALKALINE BATTERY inner feeding.

 12 key membrane keyboard: 10 keys with 0 to 9 figures. 4 dedicated led and contacts for external emergency feeding in

case of exhausted inner battery.

 “ON” key to activate the circuit.

 “ENTER” key to confirm code set and consent to the opening.

 Internal programming key for a new personal code (in some models it is protected with a sliding cover).

 TWO PERSONAL OPENING CODES WHICH CAN BE SET UP.

 DIGITS THAT CAN BE SET: minimum 6 – maximum 10. (the “ENTER” and “ON” keys are not valid in the

combination).

2. INTRODUCTION

 ALL SAFES ARE PROVIDED WITH SERVICE CODE “1 1 1 1 1 1”.

 THE SAFE OFFERS TWO CODE TO BE SET UP, WE ADVISE TO USE BOTH OF THEM TO AVOID

FORGETTING THEM.

 Before installing the safe, check that it works properly and read the instructions carefully to understand the operation.

Every time a key is pressed the green “OK” LED lights up and the buzzer sounds; pressing the “ENTER” key causes the

green “OK” LED to light up for correct procedures, or the red “ERROR” LED to light up in the case of incorrect settings.

3. FIRST APPLICATION

 Alimentation:

Unscrew the cover screw and put the batteries, of the type stated on the label, into the proper case on the rear of the lock

(see picture 1) - Screw again the cover screw.

Use only and exclusively alkaline batteries.

 Safety block removal:

remove completely (without screwing it any longer) the blocking black screw, blocking the magnet, which is marked by a

proper yellow tag.

WARNING!

To screw the black screw after removing it compromises the safe operation.

 Test for opening using the service code “1 1 1 1 1 1” (with door open and bolts extended):

1. Press “ON”, key in the service code “111111” and press “ENTER”. The green “OK” LED lights up for about five

seconds.

2. Within this time, with the green LED “ON”, turn the knob clockwise to retract the bolts. If the combination is incorrect,

the red “ERROR” LED will light up and the buzzer will sound. After three attempts with incorrect codes, the keyboard

will be disabled for one minute and this time will be indicated by the red “ERROR” LED flashing. After this time,

renewed readiness for operation will be indicated by the green “OK” LED lighting up and a beep.

4. STORING THE PERSONAL CODE:

1. With the door open and the bolts outside, press the “ON” key and, after that, the “PROGRAMMING” key place on the

inside side of the door ( see Picture 1). The “CODE” green LED lights up with a fixed light for about 10 seconds.

2. Within 10 seconds, start keying in your new personal code (min. 6 – max. 10 digits) and press “ENTER”.

3. Start keying to confirm your personal code and to press the key "Enter."

If you do not want to program the second code, wait some seconds and a multiple tone signal shall confirm that

your personal code has been stored.

In order to store a second code, go on with following procedure at the end of item 3 within 3 seconds:

4. Press the " PROGRAMMING Key"

5. Start keying to second personal code from 6 to 10 figures and to press the key "Enter."

6. Start keying to confirm your second personal code and to press the key "Enter."

A multiple tone signal shall confirm that your codes have been stored.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Technomax GMT vanaf 2009 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Technomax GMT vanaf 2009

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info