Bedienungsanleitung Technomax GT vanaf 2009 (Seite 2 von 2) (Englisch)

622560

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Istr-trony-6 cod-eng GMT S2 Pag. 2

di 2

Note:

To activate/modify the second personal code you shall always program the first one again.

5. RESETTING CODES

 Is possible cancel the personal codes pressing the “button PROGRAMMING” and the “ON” button for 5 sec.

The first code goes on 111111 and the second code will be deactivated.

Note:

If errors have been made while setting your new code, this will be indicated by the red “ERROR” LED lighting up and a beep.

Proceed in that case, a new and correct their own personal code by repeating the steps under item 4.

In memory was previously the code set to error (a new safe “111111”).

Before closing the safe, it is recommended to carry out a door open, some evidence of initiation using its personal

code.

6. OPENING THE SAFE USING YOUR PERSONAL CODE

 Press “ON”

 Enter your personal code set earlier and press “ENTER”. The green “OK” LED lights up for five seconds. Within this time,

turn the knob clockwise and open the door.

7. SIGNAL INDICATING THAT INTERNAL BATTERIES ARE GOING FLAT

When the internal batteries begins to go flat, this is indicated at the end of the opening procedure, by the red “BATTERY” LED

lighting up and a low beep tone. At this point, it will still be possible to open the safe a number of times. Replace the internal

ALKALINE batteries.

8. EMERGENCY OPENING WITH INTERNAL BATTERIES FLAT

If the failing batteries goes completely flat, as soon as the keyboard is pressed, to proceed with opening the safe:

 It is necessary to use a new 9V LR61 alkaline battery externally (see Pic. 2);

 Press the 9V battery contacts firmly on the corresponding contacts on the keyboards, ensuring that they are positioned

correctly (the “-“ of the battery touching the bigger contact and the “+” of the battery touching the small contact);

 Press “ON” and enter your personal code, followed by the key “ENTER”;

 Turn the knob clockwise to open the door.

9. ONLY VERSIONS WITH EMERGENCY KEY:

OPENING WITH EMERGENCY KEY

 Remove the adhesive label marked with the letter “E” (Pic.3);

 Insert the key and open the lock up to the stop point, turn the knob clockwise and open the door;

 By holding the door open, turn the knob until the emergence of full bolts and remove the key after rotated counter clockwise.

 To replace the label “E”;

Note: If the opening with key emergency is necessary for the oversight of their own personal code, you must store a new code

following the instructions at point 4.

IMPORTANT !

 Should replace the batteries once a year

 Even new batteries may be defective or short-term. Therefore, in the event of a malfunction of the electronic system,

ensuring, first of all, to replace the internal batteries.

 The manufacturer assumes no liability for non-compliance with the instructions or improper use of safe (penalty decay of

the guarantee).

CONTACTS

FOR

EXTERNAL

BATTERY

Pic. 2

STICKERS

KEY FOR

EMERGENCY

Pic. 3

Detail of the sliding closing to

protect the PROGRAMMING key

BATTERY CASE

Pic. 1

SCREW TO BE

REMOVED

In the smallest models the

PROGRAMMING key is

on the top.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Technomax GT vanaf 2009 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Technomax GT vanaf 2009

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info