Bedienungsanleitung Tecmate Optimate Pro 8 - TS45 (Seite 4 von 28) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

609527

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

12. PREPARING TO CHARGE

a) If necessary to remove battery from vehicle to charge,always remove grounded terminal from battery ﬁ rst.

Make sure all accessories in the vehicle are off, so as not to cause an arc.

b) Be sure area around battery is well ventilated while battery is being charged. Gas can be forcefully blown away

by using a piece of cardboard or other non-metallic material as a fan.

c) Clean battery terminals.Be careful to keep corrosion from coming in contact with eyes.

d) Add distilled water in each cell until battery acid reaches level speciﬁ ed by battery manufacturer. This helps purge

excessive gas from cells. Do not overﬁ ll. For a battery without cell caps, such as valve regulated lead acid (VRLA) or absorbed

glass mat (AGM) batteries, carefully follow manufacturer’s recharging instructions.

e) Study all battery manufacturer’s speciﬁ c precautions such as removing or not removing cell caps while charging

and recommended rates of charge.

f) Determine voltage of battery by referring to vehicle or other user’s manual and BEFORE MAKING THE BATTERY

CONNECTIONS , MAKE SURE TH AT THE VOLTAGE OF THE BATTERY YOU ARE GOING TO CHARGE MATCHES THE

OUTPUT VOLTAGE OF THE CHARGER.

13. CHARGER LOCATION.

a) Locate charger as far away from battery as DC cables permit.

b) Never place charger directly above batterv being charged; gases from battery will corrode and damage the charger. c) Never

allow battery acid to drip on charger when reading gravity or ﬁ lling battery. Do not operate charger in a closed-in area or

restrict ventilation in any way.

d) Do not set a battery on top of charger. IMPORTANT : Place charger on a hard ﬂ at surface or mount onto a vertical surface. Do

not place on plastic, leather or textile surface.

14. DC CONNECTION PRECAUTIONS

a) Connect and disconnect DC output clips only after setting any charger switches to off position and removing AC

cord from electric outlet. Never allow clips to touch each other, however should this happen no damage will result to

the charger circuit & the automatic charging programme will just reset to «start».

b) Attach clips to battery and chassis as indicated in 15(e), 15(f), and 16(b) through 16(d).

NOTE : This battery charger has an automatic safety feature that will prevent it from operating if the battery has been inversely

connected. Set charger switches to off position and/or remove AC cord from electrical outlet, disconnect the battery clips, then

reconnect correctly according to the instructions below.

15. FOLLOW THESE STEPS WHEN BATTERY IS INSTALLED IN VEHICLE. A SPARK NEAR A BATTERY MAY CAUSE BATTERY

EXPLOSION. TO REDUCE RISK OF A SPARK NEAR BATTERY :

a) Position AC and DC cords so as to reduce risk of damage by hood, door or moving engine part.

b) Stay clear of fan -blades, belts,pulleys,and other parts that can cause injury to persons.

c) Check polarity of battery posts.POSITIVE (POS, P, +) battery post usually has larger diameter than NEGATIVE (NEG,

N,–) post.

d) Determine which post of battery is grounded (connected) to the chassis. If negative post is grounded to chassis

(as in most vehicles),see (e). If positive post is grounded to the chassis,see (f).

e) For negative-grounded vehicle, connect POSITIVE (RED) clip from battery charger to POSITIVE (POS, P, + )

ungrounded post of battery. Connect NEGATIVE (BLACK) clip to vehicle chassis or engine block away from battery.

Do not connect clip to carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy gage metal part of the

frame or engine block.

f) For positive-grounded vehicle, connect NEGATIVE (BLACK) clip from battery charger to NEGATIVE (NEG. N , -)

ungrounded post of battery. Connect POSITIVE (RED) clip to vehicle chassis or engine block away from battery. Do

not connect clip to carburetor, fuel lines, or sheet-metal body parts. Connect to a heavy gage metal part of the

frame or engine block.

g) When disconnecting charger, turn switches to off, disconnect AC cord,remove clip from vehicle chassis,and then

remove clip from battery terminal.

h) See operating instructions for length of charge information.

16. FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE VEHICLE. A SPARK NEAR THE BATTERY MAY CAUSE BATTERY

EXPLOSION. TO REDUCE RISK OF A SPARK NEAR BATTERY :

a) Check polarity of battery posts. POSITIVE (POS, P, +) battery post usually has a larger diameter than NEGATIVE

(NEG,N, -) post.

b) This battery charger has an automatic safety feature that will prevent it from operating if the battery has been inversely

connected. The charger does allow charge current unless a voltage of at least 2V is sensed.

c) Connect POSITIVE (RED) charger clip to POSITIVE (POS, P, +) post of battery.

d) Connect NEGATIVE (BLACK) charger clip to NEGATIVE (NEG, N, -) battery post of the battery.

e) Do not face battery when making ﬁ nal connection.

f) When disconnecting charger, always do so in reverse sequence of connecting procedure & break ﬁ rst connection

while as far away from battery as practical.

g) A marine (boat) battery must be removed & charged on shore. To charge it on board requires equipment specially

designed for marine use.

SAFETY US & CAN

Tecmate Optimate Pro 8 - TS45 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info