640523

Tecomec Super Jolly Seite 8

8
Zoom out
Zoom in
Vorherige Seite
1/112
Nächste Seite
6
EN
9. SAFETY DEVICES
The grinder is equipped with the safety devices illustrated hereafter:
- Shield guards: they protect the operator from parts of the grinding wheel that may
come away during the sharpening process.
These guards must always be tted in place when the appliance is in use.
Always make sure the guards are efcient and tted properly. Operator safety could
be compromised if the guards are damaged and/or cracked.
- Switch: the appliance features a safety switch with release coil. In the case of a
sudden power failure, the switch trips automatically and disconnects the appliance
from the mains. The appliance will not start even if the power supply is suddenly
restored. You need to reset the switch to start the appliance again.
10. INTENDED USE
This appliance is an electrical grinder for chains used in chain saws.
- Use the appliance exclusively for the types of chains stated in the technical data
chart.
- Do not use the appliance to cut or grind anything other than the chains envisaged.
- Secure the appliance rmly to the bench or wall.
- The appliance must not be used in corrosive or explosive environments.
- Any other use is to be considered improper.
The manufacturer is not liable for damages following improper or incorrect use of
the appliance.
11. UNPACKING
The grinder is supplied already completely assembled.
12. STANDARD SUPPLY (FIG.2)
1 - Grinder base unit 9 - Sharpening template – 3/4’’
2 - Instruction manual 10 - Dressing brick
3 - Test card 11 - 4 mm Allen wrench
4 - Grinding wheel Ø 145x3.2x22.2 12 - 5 mm Allen wrench
5 - Grinding wheel Ø 145x4.7x22.2 13 - M8x80 screw
6 - Grinding wheel Ø 145x8x22.2 14 - M8 nut
7 - Operating handle 15 - Washer for M8 screw
8 - Sharpening template 16 - Chain stop kit - 3/4”
13. TESTING THE GRINDING WHEEL
Hold the grinding wheel up by its central hole. Knock the edge of the grinding wheel
 gently with a non-metallic object. If it makes a numb non-metallic noise it
means that the wheel could be damaged: do NOT use it!
14. INSTALLATION
ATTENTION
Do not install the appliance at eye level. You are recommended to install it at a height
of no more than 1.2-1.3 meters off the oor.
The appliance can be bench mounted or wall mounted.
14.1 BENCH MOUNTING (FIG.4)
Use 2 M8 screws complete with washers and nuts (material supplied), inserted in the
securing holes F4. Make sure you position the base unit on the bench as illustrated
in the detail.
14.2 WALL MOUNTING (FIG.5)
Use two dowels with relative screws complete with washers (material not supplied),
inserted in the securing holes F6.
14.3 SECURING THE OPERATING HANDLE (FIG.6)
Completely screw the operating handle I7 on the screw V7.
15. CHAIN INFORMATION
The chain must be completely inspected before sharpening it to make sure it is intact.
 
1 Top part 1 Connection link
2 Top cutting angle 2 Left cutter
3 Side cutting angle 3 Right cutter
4 Sharpening recess 4 Driving link (pulling link)
5 Depth gauge 5 Rivet
6 Bit
7 Heel
8 Rivet hole
16. CHAIN IDENTIFICATION
- Before you start to sharpen, you need to know the type of chain and the relative
adjustment angles. These characteristics are written in the owner’s manual of the
chain saw on which the chain is tted or on the chain pack.
- The chain identication code is usually written on the driving link.
- You can also identify the chain using a template or gauge.
- Consult the CHAIN CHART at the end of this manual.
The columns in this chart provide the following information:
A
÷ 2
Chain pitch
B
Driving link width
C
Top sharpening angle (vise rotation)
D
Cutting angle (arm rotation)
E
Down angle (vise inclination)
F
Gauge depth
G
Grinding wheel thickness
H
Grinding wheel code
I Oregon chain codes N Carlton chain codes
L Windsor chain codes O Stihl chain codes
M SARP chain codes P EM chain codes
16.1 INSTRUMENTAL MEASUREMENTS (FIG.9)
a - Measure the gauge depth using the suitable shape.
b - Put the template on this side and measure the chain PITCH.
c - Put the template on this side to measure the cutter length.
d - The driving link width is measured using a suitable instrument (i.e. gauge).
17. GRINDING WHEEL WARNINGS
- Use a grinding wheel suitable for the type of chain to be sharpened; consult the
chain chart at the end of the manual.
- Do not force the grinding wheel on the hub and do not alter the centering hole
diameter. Do not use grinding wheels that do not t perfectly in place.
- Use exclusively clean and perfect intact hub and ange to t the grinding wheel.
- Make sure the outside diameters of the hub and ange are identical.
18. FITTING THE GRINDING WHEEL
- Loosen the screw V10 and turn the guard P10 
- Remove the screw V8 and the ange F8 on the hub 
- Choose the grinding wheel based on the type of chain to be sharpened (column H
in chain chart).
- Insert and perfectly center the grinding wheel in the dedicated seat on the hub
.
- Insert the ange F8 and tighten the screw V8 .

If the grinding wheel is tted with the anges too tight, it could break during
use and put the operator at risk. To avoid such risk, tighten screw M6x25
to 7 Nm (if possible, check with dynamometric spanner).
- Close the guard again P10 and tighten the relative screw V10 .
18.1 REPLACING THE CHAIN STOP KIT (FOR 3/4” CHAINS)
- The special chain stop kit must be tted for 3/4” chains only.
- Loosen and unscrew the knob P14 (g. 14A).
- Remove the chain stop kit K1 (g. 14B).
- Fit the 3/4” chain stop kit K2 (g. 14C and 14D).
- Screw up and tighten the knob P15 (g. 14E).
19. CHECKING THE ASSEMBLY OF THE GRINDING WHEEL
- Stand at the side of the grinding wheel, start the grinder and visually make sure
the grinding wheel does not oscillate sideways or crosswise, consequently causing
abnormal vibrations.
- If this should be the case, stop the appliance immediately and check if the grinding
wheel has been tted correctly. If necessary, replace the grinding wheel with another
original one.
Always check a freshly tted grinding wheel at working speed for at least one
minute before you start grinding, standing at a safe distance and making sure
nobody else approaches the appliance.
… 8 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Tecomec Super Jolly wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info