Bedienungsanleitung Tectro tscs 126 (Seite 11 von 22) (Englisch)

134620

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

111

COOL, HEAT, and FAN ONLY Operation

1. If the AUTO mode is not comfortable, you may manually override the settings by using COOL, DRY,

HEAT (HEAT PUMP units only), or FAN ONLY modes by pressing button ባ.

2. Push

the ▲ or ▼ button (ቤ and ብ) to set the desired room temperature. When in COOLING mode, the

most comfortable settings are 21ºC or above. When in HEA

TING mode, the most comfortable settings

are 28ºC or below.

3. Push the Fan button ቦ to select the FAN mode of AUTO, HIGH, MED or LOW.

4. Push

the On/off button ቢ. The operation lamp lights and the air conditioner starts to operate per your

settings. Push the On/off button ቢ again to stop this unit operation.

DRY Operation

1. Push the Mode button ባ to select DRY.

2. Push the ▲ or ▼ button (ቤ and ብ) to set the desired temperature from 21 C to 28 C.

3. Push the On/off button ቢ. The operation lamp lights and the air conditioner starts to operate in the DR

mode. Push the On/off button ቢ again to stop this unit operation.

TIMER Operation

Push Timer on/off button (ቪ and ቫ) to set the on and off times of the unit. The effective operation time

set by the remote controller for the timer function is limited to a period of between 0.5 and less than 24

hours.

1. T

o set the STARTING time.

1.1

Push the Timer on button ቪ, then the remote controller display shows ON TIMER, the last set time for

the starting operation and the signal "Hr" will be shown on the digital display area. Y

ou are now ready

to reset the time to START the operation.

1.2

Push the Timer on button ቪ again to set desired unit start time.

1.3

After setting the Timer on ,there will be half a second delay before the remote controller transmits the

signal to the air conditioner. Then, after approximately another 2 seconds, the signal "h" disappears

and the set temperature will re-appear on the digital display.

2. To set the STOPPING time.

2.1

Push the Timer off button ቫ and the remote controller display will show OFF TIMER and the last set

time for the timer off operation in hours will be shown on the Timer display area. You are now ready

to reset the time of the STOP operation.

2.2

Push the Timer off button ቫ again to set the time you want to stop the operation.

2.3

After setting the Timer off, there will be half a second delay before the remote controller transmits

the signal to the air conditioner. Then, after approximately another 2 seconds, the signal "h" disappe-

ars and the set temperature will re-appear on the digital display



NOTE!

Due to the difference of the set temperature of the unit and the actual indoor temperature, the

Air Conditioner when in DRY mode will automatically operate many times without running the

COOL and FAN mode.



NOTE!

The FAN ONLY mode cannot be used to control the temperature. In this mode, only steps 1, 3 and

4 are applicable.

man_TSCS126_uk.qxd 21-12-2007 14:20 Pagina 111

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tectro tscs 126 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Tectro tscs 126

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info