Bedienungsanleitung Tefal PT7035 - Intense Pure Air turbo (Seite 9 von 27) (Englisch)

724970

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

CHILD LOCK FUNCTION

To activate it, press the light button (10) for 3 seconds, until the child lock indicator turns on. To exit this mode,

press the light button again for 3 seconds, until the child lock indicator turns o.

Under the child lock function, the other buttons are locked.

TIMER / DELAYED START

• If the appliance is on: you can use this button to dene the operating duration. Briey press the button to

select the number of operating hours desired (1, 2, 4 or 8) and the appliance will automatically turn o at the

end of the selected period.

• If the appliance is o: briey press the button to set the appliance to turn on in a certain number of hours

(1, 2, 4 or 8).

MAINTENANCE

Always switch the appliance o with the button (13) and unplug it before conducting any maintenance

operation.

You can clean the appliance with a slightly damp cloth.

IMPORTANT: Never use abrasive products which could damage your appliance’s appearance.

This data is based on an average use of 8 hours per day at speed 1. The recommended frequency for cleaning and

replacing the lters may vary depending on the duration of use and the operating environment.

The lter needs to be cleaned or replaced when the corresponding indicator is turned on.

Note: when your appliance stops ltering, please check if you need to change the lter.

• When the pre-lter needs to be cleaned, its warning light on the control panel switches on.

• When the 2 in 1 HEPA and active carbon lter needs to be replaced, its warning light on the control panel switches

on.

• When the NanoCaptur lter needs to be replaced, its warning light on the control panel switches on.

The NanoCaptur lter contains translucent granules which change color according to the formaldehyde

absorption rate. Refer to the color chart on the inside of the panel or the lter itself to establish the lter saturation

rate. Once the saturation rate has reached its maximum, the lter must be replaced. You have to check the lter

saturation rate every six months.

• The pre-lter can be re-used: remove the dust using a vacuum cleaner or wash with water.

IMPORTANT: resetting the filters

Once the lter has been replaced, hold down the lter function for 3 seconds.

Forced reset:

If you have replaced a lter before its end of life, force the reset of the lter replacement cycle:

1. When the appliance is on, hold the reset button (11) for 3 seconds.

2. Press the reset button briey to select the lter you have changed.

3. After selecting the lter to reset, hold the reset button (11) for 3 seconds. The electronic meter is then reset.

4. If no button is activated for 10 seconds in forced reset mode, the reset mode is canceled.

Filters Action Cycles

Pre-lter Clean Every 2 or 4 weeks

2 in 1 HEPA and active carbon lter Replace Every 36 months

NanoCaptur lter Replace Every 12 months

FILTERS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tefal PT7035 - Intense Pure Air turbo Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info