Bedienungsanleitung Teka CB380 (Seite 31 von 57) (Deutsch, Englisch, Französisch, Portugiesisch, Spanisch)

18320

Zoom out

Zoom in

Vorherige Seite

1/57

Nächste Seite

REVERSING THE OPENING OF THE DOORS (some models only) see fig. 3

1) It is advisable to lean the refrigerator at an angle of about 45°, since it is necessary to

work on the bottom of the appliance in order to remove the lower hinge.

2) Remove the plinth, if fitted.

3) Remove the lower hinge (and relative washers), by loosening screws A as shown in

the figure.

4) Remove the lower door.

5) Remove the middle hinge (and relative washers), by loosening screws B as shown in

the figure 3. Models with the upper tall door (fig. 7d – inside upper portion of the top

door), before removing screws that fix the central hinge (between fridge and freezer door)

open the top door and remove cap M and plastic insert L. When reversing the doors, the

doors need to be supported at all times.

6) Remove the top door. Remove screw N from the right bottom hinge (fig 7e – bottom

section of the appliance with kickplate removed). Take the left bottom hinge from the pla-

stic bag and fix it to the bottom of the appliance with the screw you removed from the

right bottom hinge.

7) Remove the plastic film, covering the upper left-hand hinge, from the facing.

8) Unscrew journal C from the upper right-hand hinge and refit it on the left. Models with

the upper tall door (fig. 7c – inside upper portion of the top door), remove caps F-G, pivot

D and the right upper hinge, taking away the screw. Take the left upper hinge (H) from

plastic bag and fix it with the screw you have removed. Fix pivot D with washer to the left

upper hinge. After transferring the hinge to the left hand side, the plastic insert (L) which

covers this mechanism needs to be altered, the membrane of cap G needs to be broken

so that its fits back into place.

9) Replace the doors working in a reverse fashion (6-5-4-3-2); remembering to refit the

spacing washers between door and hinge.

10) Move the vertical handles, if they have been supplied, from the left hand side to the right

hand side, by adjusting the relevant screws. For handles marked “M”, move them diagonally

across from left to right. Remove the adhesive label from the left handle, take a new label

from the accessory pack, remove the protective strip and attach it to the right handle.

11) Restore the appliance to an upright position.

N.B. Correct alignment of the doors is obtained by adjustment of the middle hinge.

REVERSING THE OPENING OF THE DOORS (some models only) see fig.7

For models with a bottom hinge both on the right and the left.

1) We recommend that the refrigerator be tilted about 45 degrees.

2) Remove the screws (A) that hold the central hinge in place. Models with the upper tall

door (fig. 7d – inside upper portion of the top door), before removing screws that fix the

central hinge (between fridge and freezer door) open the top door and remove cap M and

plastic insert L. When reversing the doors, the doors need to be supported at all times.

3) Remove the top door. Remove screw N from the right bottom hinge (fig 7e – bottom

section of the appliance with kickplate removed). Take the left bottom hinge from the pla-

stic bag and fix it to the bottom of the appliance with the screw you removed from the

right bottom hinge.

4) Remove the central hinge.

5) Remove the bottom door.

6) Remove the plastic membrane covering the top left hinge and the lower left hinge from

the panel and the plinth.

7) Remove the pin (B) from the bottom right hinge and reassemble on the left.

8) Remove the pin (C) from the top right hinge and reassemble it on the left. Models with

the upper tall door (fig. 7c – inside upper portion of the top door ), remove caps F-G, pivot

D and the right upper hinge, taking away the screw. Take the left upper hinge (H) from

plastic bag and fix it with the screw you have removed. Fix pivot D with washer to the left

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Teka CB380 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info