Bedienungsanleitung Teka HPE 635 (Seite 14 von 25) (Deutsch, Englisch, Französisch, Portugiesisch, Spanisch)

529595

Zoom out

Zoom in

Vorherige Seite

1/25

Nächste Seite

ENGLISH

PROGRAMMING AND OPERATING THE PYROLYTIC FUNCTION

Follow the instructions below to carry out a

pyrolytic cleaning cycle:

1 IMPORTANT: Remove all accessories

(shelves, grids, side supports to hold up

the shelves, telescopic guide rails) from

inside the oven.

2 Turn the cooking control dial to Pyrolysis

position .

3 Next, press the

PIRO

key, the word PIRO

should appear on the timer display.

4 After a few seconds, P2 (pyrolysis pro-

gramme 2) will appear on the timer display,

the BACK symbol will also remain lit up.

5 You can now change the pyrolysis program-

me to P1, P2 or P3 by pressing the + or –

keys:

P1: Minimum programme. Duration 1 hour

P2: Standard programme. Duration 1 hour

and 30 minutes

P3: Maximum programme. Duration 2

hours

6 You will hear 2 consecutive beeps after

several seconds or by pressing the

PIRO

key confirming the chosen programme.

7 You can still change the pyrolysis program-

me by pressing the

PIRO

key and the + or

– keys.

8 After a short time, you will see the time

remaining for the selected programme to

end and the symbols and BACK lit up

on the timer display. The pilot light will

turn on and the oven door cannot be ope-

ned, as the heating will have begun.

IMPORTANT: At this point, the oven is pro-

grammed and the pyrolytic cleaning cycle is

underway. During the cycle, none of the timer

functions can be selected, except the child

lock. Do not try to open the oven door as it

may interrupt the cleaning process.

9 When the pyrolytic cleaning cycle has finis-

hed, an alarm will sound, the symbol

will flash and you will see the correct time

on the display.

10 Press any of the timer’s keys to disable the

alarm.

11 Set the cooking control dial to position .

12 The oven’s heating process has ended,

however the oven is extremely hot and can-

not be used. The cooling motor will opera-

te until the oven cools down, pilot light

will remain on and the symbol will

flash on the timer display.

IMPORTANT

The cooling process may last up to 2 hours

owing to the high temperatures inside the

oven.

13 Once the oven has cooled down, pilot light

will automatically turn off.

14 Press the

PIRO

key to stop symbol 9 flas-

hing. .

IMPORTANT

To open the door (pilot light on), the control

dial must be in position . If you did not follow

instruction 11 set the control dial to position

and wait a few minutes until the door unlocks

and the pilot light switches off.

15 Open the oven door and wipe the inside

with a damp cloth, cleaning up the ash

from the cleaning cycle. Areas in the oven

that are difficult to access will need to be

cleaned with a non-metallic fibre scourer.

16 Once the oven is clean, do not forget to

replace the supports and accessories.

17 The oven is now ready to be used.

IMPORTANT: If any incidents are detected in

the programming and operating of this func-

tion, consult the section “Incidents while

Operating the Pyrolytic Function”.

CANCELLING THE PYROLYTIC CYCLE

Pyrolysis is an automatic function and therefo-

re can only be activated from the timer pro-

gramme. To cancel a cleaning cycle it is neces-

sary to reset the oven, following the instruc-

tions below:

1 Set the control dial to position .

2 Unlock the oven door.

3 Cancel the pyrolysis programme.

1 Set the control dial to position . The

oven will no longer heat up. Wait a few

minutes before continuing with the instruc-

tions to unlock the door.

2 Unlock the oven door. To cancel the clea-

ning cycle, the oven door must be unloc-

ked. To do so, consider the following:

a) Unlocking the door 30 minutes after

the cleaning cycle. If the oven has been

operating for more than 30 minutes, the

door will unlock automatically once the

oven has cooled down to the safe tem-

perature. Then, pilot light will switch

off.

b) Unlocking the door in the first 30 minu-

tes (at a low temperature). Within the

first 30 minutes the oven door will

unlock automatically. Follow the instruc-

tions below:

1 Turn the control dial to position .

2 Wait for approximately 1 minute.

3 Turn the control dial to position .

4 Approximately, 1 minute later pilot

light will turn off and the oven door

can be opened.

3 Cancel the pyrolysis programme. To can-

cel the programme you must:

1 Turn the control dial to position

and then to position .

2 Press the

PIRO

key for 3 seconds.

3 Next, the timer display will show the

correct time and symbol will disap-

pear.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Teka HPE 635 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info