Bedienungsanleitung Teka it 641 exp (Seite 13 von 22) (Englisch)

336432

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

SWITCHING THE APPLIANCE ON

1 Touch the on sensor (1) for at least

one second. The Touch Control will acti-

vate, you will hear a beep and the indi-

cators will turn on. If any of the cooking

areas is hot, the corresponding indicator

will alternate between showing a H and

a 0.

The following action must be carried out

within 10 seconds or the touch control will

automatically switch off.

When the touch control is activated, it can

be disconnected at any time by touching

the sensor (1), even if it has been

blocked (blocking function activated). The

sensor (1) always takes priority for dis-

connecting the touch control.

SWITCHING THE HOTPLATES ON

The hotplates will be found deactivated,

with their respective power indicators (3)

at 0, until a power level is selected. If all

the hotplates are set at 0, you have 10

seconds to activate any of them, otherwise

the touch control will automatically turn off.

Use the sensors and (4/5) to select

a power level. If you touch the sensor

(5), the plate will switch to level 1 and,

for each additional stroke, it will go up one

level until reaching the maximum value of

P. Using the sensor (4), you can redu-

ce the power level.

For a fast powering up at maximum power:

with the plate at 0, touch the sensor (4)

once. The plate will directly activate at

level 9.

By continuing to press down on any of

these two sensors (4) or (5), they

will repeat the action every half a second,

without needing to press consecutively.

SWITCHING THE HOTPLATES OFF

With the sensor (4), lower the power to

level 0.

The hotplate will automatically power off.

For a fast power up: no matter what the

power level, by simultaneously pressing

the sensors and (5/4), the plate will

immediately power off.

By powering off a hotplate, an H will be

shown on the power indicator, if the glass

surface is at a high temperature, indicating

that there a risk of burning. When the tem-

perature has fallen, the indicator will power

off if the top is disconnected or, if it is tur-

ned on, it will indicate a 0.

POWERING OFF THE DEVICE

At any time, you can disconnect the top by

pressing the sensor (1). When doing

this, an acoustic signal is heard and the

power indicators (3) will turn off, except if

there is a residual H heat indicator active

due to the plate temperature.

Locking the sensors

Using the locking sensor (8), you can

block all the sensors on the touch control

panel. This will make it possible to avoid

undesired accidental operations occurring

or children being able to manipulate the

control.

Bear in mind that with the touch control

powered up, the on/off sensor (1)

makes it possible to turn it off even if the

locking is activated (pilot 10 on). On the

other hand, if the touch control is turned

on, the locking function does not allow for

activating the on/off sensor (1). You

should first deactivate blocking.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Teka it 641 exp Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info