Bedienungsanleitung Teka TKD 1490 (Seite 5 von 74) (Englisch, Portugiesisch, Spanisch)

781280

Zoom out

Zoom in

Vorherige Seite

1/74

Nächste Seite

P.08 P.09

Install Washing Machine Install Washing Machine

3.Ensure the positioning status of washing machine. Loosen the lock nut with spanner

and turn the leg with hand until it closely contacts with the floor. Press the leg with one

hand and fasten the nut closely to the cabinet with the other hand.

4.After being locked properly, press four corners again to make sure that they has been

adjusted properly. If it is still unstable, it has to repeat Steps 2 and 3.

Connect inlet pipe

Connect the inlet pipe as indicated in the figure.

For the model which has hot valve , please connect

the hot vale to hot water tap. Energy will decrease

automatically for some program.

Install inlet pipe

1.Connect the elbow to tap and fasten it

clockwise.

2.Connect the other end of inlet pipe to the inlet

valve at the backside of washing machine and

fasten the pipe tightly clockwise.

Notes: after connection, if there is any leakage

with hose, then repeat the steps to connect inlet

pipe. The most common type of tap shall be

used to supply water. If tap is square or too big,

then standard tap shall be changed.

Place outlet hose

There are two ways to place the end of outlet hose:

1.Put it beside the water trough.

Hole plug

This Hole plug is used to jam the hole on the back

cabinet.

Unpacking the washing machine

Unpack your washing machine and check if there is any damage during the transportation.

Also make sure that all the items (as shown in Page 5) in the attached bag are received.

If there is any damage to the washing machine during the transportation, or any item is

missing, please contact the local dealer immediately.

Dispose the packing materials

The packing materials of this machine may be dangerous to kids. Please dispose them

properly and avoid easy touch by kids. Please dispose the related packing materials

according to the relevant local regulations. Please do no throw the packing materials

away together with the other daily living rubbishes.

Remove transport bolts

Before using this washing machine, transport bolts

must be removed from the backside of

this machine. Please take the following steps to

remove the bolts:

1.Loosen all bolts with spanner and then remove them.

2.Stop the holes with transport hole plugs.

3.Keep the transport bolts properly for future use.

Select the location

Before installing the washing machine, the location characterized as follows shall be

selected:

- Rigid, dry, and level surface (if not level, please make it level with reference to the

following figure “Adjust Leg”)

- Avoid direct sunlight

- Sufficient ventilation

- Room temperature is above 0 C

- Keep far away from the heat resources such as coal or gas.

Make sure that the washing machine will not stand on power cord.

Do not install the washing machine on the carpet floor.

Adjust Leg

1.When positioning the washing machine, please

first check if the legs are closely attached to the

cabinet. If not, please turn them to their original

positions with hand or spanner and tighten the

nuts with spanner.

2.After positioning the washing machine, press

four corners on top cover of washing machine

in sequence. If the washing machine is not

stable when being pressed, this leg shall be

adjusted.

5.Put a solid cylinder (e.g. pop cans) oppositely on the top cover of the washing machine from in

the left, right, front and back directions. If the cylinder keeps stable, the washing machine is

positioned level. If it rolls, the washing machine is positioned unlevel. The rolling direction is the

direction of lower ground surface. Then, the two legs in this direction shall be raised at the same time

until the washing machine is level. Steps 1~3 are repeated to make the bottom legs closely against

the ground and the nuts shall be locked tightly.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Teka TKD 1490 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info