Bedienungsanleitung Telair Energy 4010g (Seite 18 von 40) (Englisch)

688852

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Energy 4010 G Vers. 001

6.5 Control and alarm functions (Fig. 30)

2 Display: when the generating set has started

up, the total running hours will be displayed.

Press the key provided below the control panel

display unit (Fig.30 Ref.9) to display the number

of generating set operation hours since the latest

engine oil change.

3 High temperature indicator: this warning light

will light up when the temperature of the

generating set goes over its safety value; the

engine will stop at the same time.

4 Engine oil minimum level indicator: this

warning light will light up to indicate that oil in the

engine has gone below the minimum level. A

safety system will kill the engine automatically to

prevent failures.

5 Engine startup failed: this warning light will

light up to indicate that the generating set has not

started up, after all four start-up attempts.

7 Change oil: this warning light will light up when

the engine has reached 100 running hours since

the latest oil change. Every time the oil is

changed, the After-sales service staff must reset

the timer to zero.

8 Fuel warning: this warning light will light up

when the fuel level inside the extra tank has gone

below its reserve level (about 4 litres)

9 Display time changeover switch: press this

switch to display the running hours since the

latest engine oil change.

10 Reset: When the display shows characters

without any apparent logic, the panel needs to be

reinitialised. Press the Reset key (Fig.30 Ref. 10)

and, holding it down, switch on the panel. When

4 zeroes (0000) are displayed, the panel has

been reinitialised.

6.6 Control panel alarm causes and resetting

During generating set use, alarm signals may be

displayed referring to engine oil checks. After

checking the engine oil, the control panel must

be reset in the following way:

Alarm: the red ‘service’ light is flashing.

Cause: 50 hours have elapsed since the latest

engine oil change and oil level should be

checked.

How to reset the alarm: press the partial

counter key (Fig.30 Ref.9) and while holding it

down, turn the panel on and release the push-

button when the unit has started up

Alarm: the red ‘service’ light is lit.

Cause: 100 hours have elapsed since the latest

engine oil change and engine oil should be

changed.

How to reset the alarm: turn on the panel and

wait for the generating set to start. Now press the

button hidden under the small hole in the bottom

left corner (Fig.30 Ref.10) and release it

immediately thereafter.

Wait a couple of minutes before turning the

generating set off.

In certain situations, the data contained in the

microprocessor inside the panel may be altered.

This may be because the battery is very low, or

because the cables used to connect the battery

to the set have too small cross-sections. Altered

processor data may prevent the generating set

from running. In order to restore the generating

set operating efficiency, proceed as follows:

Alarm: the display unit shows random

characters.

Cause: malfunctioning due to low voltage during

start-up (low battery, cable cross-section too

small). Reinitialise the panel.

How to reset the control panel: press the

button (Fig.30 Ref. 10) and while holding it down,

turn on the control panel. Only release the push-

button when 4 zeros (0000) are displayed. The

panel has been reinitialised.

6.7 Automatic Version (optional)

If you wish the start-up batteries to be recharged

automatically in the En 4010 G generating sets, it

is possible to install the ASP (optional) automatic

control panel (fig.32) instead of the manual

control panel.

The elements making it up are:

1 ON/OFF switch for the start-up and switch-off

function

2 Display

3 High temperature indicator

4 Minimum oil level indicator

5 Start-up failed indicator

6 Generator running indicator (flashing)

7 Maintenance request indicator

8 Fuel reserve indicator

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Telair Energy 4010g Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info