Bedienungsanleitung Telair TIG3000D Inverter generator (Seite 21 von 48) (Englisch)

688827

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

Vers. 002

TIG 3000 D

The generator will start when the connected bat-

tery voltage drops below the set threshold (de-

fault is 12.0 volts).

Once the generator has started the display

shows in sequence the icons

The generator will stop automatically when the

connected battery voltage rises above the set

threshold (default is 13.8 Volt).

In any case, the generator will remain in opera-

tion for at least 15 minutes.

Note that the required battery charging time

changes according to the battery capacity,

maximum current delivered by the battery

charger used and the ambient temperature in the

battery environment.

In the event that, in addition to the battery

charger, a minimal default load is connected

(around 300 Watt), the generator will not shut off.

The AUTO mode can be activated whether the

generator is active or on stand-by.

The AUTO mode is automatically deactivated

when the START/STOP button is pressed.

8.7 Remote starting

The generator can be started using a remote

control from another device (battery charger,

SMS box, etc.), using the REMOTE connector

(Fig. 22 ref. 4). The galvanically isolated C and

NO terminals are attached to this connector by a

relay controlled from an external device.

To carry out a remote start-up, turn the switch on

the control panel to the ON position (Fig. 30 ref.

1), without starting the generator. At this point the

generator is ready to receive a command on the

REMOTE connector: when the contact is closed,

the generator will start and it will stop when the

contact is opened.

Should any high-level alarms come from

the generator, such as oil or temperature, the

signal from the D+ input, or pressing the

START/STOP button on the control panel will

take priority over the REMOTE On-Off command.

The oil alarm and the D+ signal prevent remote

start-up until the START/STOP button on the

control panel has been pressed.

8.8 BOOST Function

The BOOST function must be activated when a

single load close to the maximum power must be

connected.

To activate this function, hold down the Menu key

for 3 seconds; the corresponding LED lights up

and even in the absence of any load the engine

increases its rpm.

To turn off the function, press and hold the Menu

key again for 3 seconds; the corresponding LED

will go off and the engine rpm slows down.

8.9 Alarm messages and causes

The alarms described here stop the generator.

An alarm condition is cancelled by pressing the

START/STOP button once; the generator then

reverts to a status in which it can be restarted.

Before doing this, you must eliminate the condi-

tion that caused the stop and the alarm.

8.9.1 Over load

the maximum

permitted load has been exceeded, the generator

stops and the red alarm LED lights up (Fig.30 ref.

8).

8.9.2 Short circuit

there is a

short circuit on 230 V output, the generator stops,

the red alarm LED lights up (Fig.30 ref. 8).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Telair TIG3000D Inverter generator Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Telair TIG3000D Inverter generator

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info