Bedienungsanleitung Telefunken C55U320A4CW (Seite 9 von 32) (Englisch)

634667

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

English - 43 -

Switching On/Off

To Switch the TV On

Connect the power cord to a power source such as a

wall socket (220-240V AC, 50 Hz).

To switch on the TV from standby mode either:

• Press the Standby button, Programme +/- or a

numeric button on the remote control.

• Press the Standby button or Programme +/- on

the TV.

The TV will then switch on.

To Switch the TV Off

Press the Standby button on the remote control or

press the Standby button on the TV, then the TV

switches into standby mode.

To power down the TV completely, unplug the

power cord from the mains socket.

Note: When the TV is switched into standby mode, the

standby LED can blink to indicate that features such as

Standby Search, Over Air Download or Timer is active. The

LED can also blink when you switch on the TV from standby

mode.

First Time Installation

When turned on for the first time, the language

selection screen is displayed. Select the desired

language and press OK.

On the next screen, set your preferences using the

directional buttons.

Note: Depending on the Country selection you may be asked

to set and conrm a PIN at this point. The selected PIN cannot

be 0000. You have to enter it if you are asked to enter a PIN

for any menu operation later.

About Selecting Broadcast Type

Aerial: If Aerial broadcast search option is turned on,

the TV will search for digital terrestrial broadcasts after

other initial settings are completed.

Cable: If Cable broadcast search option is turned on,

the TV will search for digital cable broadcasts after

other initial settings are completed. According to your

other preferences a conrmation message may be

displayed before starting to search. Select YES and

press OK to proceed. To cancel operation, select NO

and press OK. You can select Network or set values

such as Frequency, Network ID and Search Step.

When nished, press OK button.

Note: Searching duration will change depending on the

selected Search Step.

Satellite: If Satellite broadcast search option is

turned on, the TV will search for digital satellite

broadcasts after other initial settings are completed.

Before satellite search is performed some settings

should be made. Antenna Type menu will be

displayed rst. You can select Antenna Type as

Direct, Single Satellite Cable or DiSEqC switch by

using “ ” or “ ” buttons.

•Direct: If you have a single receiver and a direct

satellite dish, select this antenna type. Press OK to

continue. Select an available satellite on the next

screen and press OK to scan for services.

•Single Satellite Cable: If you have multiple

receivers and a single satellite cable system, select

this antenna type. Press OK to continue. Congure

settings by following instructions on the next screen.

Press OK to scan for services.

•DiSEqC switch: If you have multiple satellite dishes

and a DiSEqC switch, select this antenna type.

Press OK to continue. You can set four DiSEqC

options (if available) on the next screen. Press OK

button to scan the rst satellite in the list.

Analogue: If Analogue broadcast search option is

turned on, the TV will search for analogue broadcasts

after other initial settings are completed.

Additionally you can set a broadcast type as your

favourite one. Priority will be given to the selected

broadcast type during the search process and the

channels of it will be listed on the top of the Channel

List. When nished, press OK to continue.

You can activate Store Mode option at this point.

This option will congure your TV’s settings for store

environment and depending on the TV model being

used, the supported features of it may be displayed

on the top of the screen as an info banner. This option

is intended only for store use. It is recommended to

select Home Mode for home use. This option will be

available in System>Options>More menu and can

be turned off/on later.

Press OK button on the remote control to continue

and the Network/Internet Settings menu will be

displayed. Please refer to Connectivity section to

congure a wired or a wireless connection. After the

settings are completed press OK button to continue.

To skip to the next step without doing anything press

the Rapid advance button on the remote.

After the initial settings are completed TV will start

to search for available broadcasts of the selected

broadcast types.

After all the available stations are stored, scan results

will be displayed. Press OK to continue. The Edit

Channel List menu will be displayed next. You can

edit the channel list according to your preferences or

press the Menu button to quit and watch TV.

While the search continues a message may appear,

asking whether you want to sort channels according

to the LCN(*). Select Yes and press OK to conrm.

(*) LCN is the Logical Channel Number system that organizes

available broadcasts in accordance with a recognizable

channel number sequence (if available).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Telefunken C55U320A4CW Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Telefunken C55U320A4CW

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info