11
Introduction
The 2in1 (item no. 55412) Universal Remote Control is designed to control up to 2 devices.
The Universal Remote Control contains a library of codes that are pre-programmed into the
remote control. This library covers nearly all the TV and SAT products on the market today. The
SAT mode key can also be programmed to control Cable Decoder, DVBT, ADSL box.
Inserting the batteries
Two CR2032 batteries are included in delivery. In order to use the remote control, open the
battery compartment and remove the protective foil. If the batteries need changing always use
two NEW CR2032 batteries.
1. Open the cover on the back of the remote control.
2. Check the +/– polarity on the batteries and inside the compartment.
3. Insert the batteries and close the cover.
Programming your modes
1. Make sure your equipment is switched on (for example TV).
2. Press the key that corresponds to the type of equipment you want to control:
TV:
television set or
SAT:
satellite receiver, cable decoder, DVBT, ADSL box.
3. Press and hold the Setup (4) key until the red indicator (10) lights continuously. Release the
Setup key.
5. While the indicator lamp is on, with the keys
CH+
(1st number),
CH-
(2nd number),
VOL+
(3rd number), and
VOL-
(4th number), enter the 4-digit code.
EXAMPLE: To enter code
0039
, do not press the keys
CH+
and
CH-
, press
VOL+
three times
and
VOL-
nine times. The red indicator lamp flashes whenever a key is pressed.
6.
To save the code, press Mute key (5). The red indicator lamp goes off. Should the code entered
not be on the list, the red indicator lamp flashes rapidly during 3 seconds and then goes off.
7. Point the remote in the direction of your TV and press the Power button (2). Your device
should turn off. Check other functions. If certain functions are not responding this indicates
that the entered code is not the correct one. In that case repeat the above procedure with the
next corresponding code of your brand.
8. Repeat this procedure from step 1 for the other equipment you want to control.
Code search
If your equipment (TV, SAT etc.…) does not respond, try the other codes for your brand. If it still
doesn’t respond, try the Code Search method.
1. Make sure your equipment is switched on (for example TV).
2. Press the key that corresponds to the type of equipment you want to control:
TV:
television set or
SAT:
satellite receiver, cable decoder, DVBT, ADSL box.
3. Press and hold the Setup (4) key until the red indicator (10) lights continuously. Release the
Setup key.
4. Direct the remote control towards your appliance and try to switch it off by simply pressing the
Power key (2). Should the appliance not switch off, press (2) as many times as required (up to
300 times), until the appliance switches off. Between two subsequent key presses, give the
red indicator lamp enough time to turn off and light up again (about 1 second). Proceeding
this way will enable you to see whether the appliance responds or not.
5. Immediately after the appliance to be controlled switches over to standby, press Mute key (5)
to save the code. The red indicator lamp goes off.
6. Point the remote in the direction of your TV and press the Power button (2). Your device
should turn off. Check other functions. If certain functions are not responding this indicates
that the entered code is not the correct one. In that case repeat the above procedure with the
next corresponding code of your brand.
7. Repeat this procedure from step 1 for the other equipment you want to control.
If all codes have been searched, the red LED indicator will blink for about 3 seconds.
Note:
if certain functions of your equipment can’t be controlled you have to find a different code
for your brand.
Identifying codes found using the search procedure
1. Press the key that corresponds to the type of equipment you want to control:
TV:
television set or
SAT:
satellite receiver, cable decoder, DVBT, ADSL, …
2. Press and hold the Setup (4) key until the red indicator (10) lights continuously. Release the
Setup key.
3. Press the Setup (4) key a second time.
4. To visualise the first code digit, press
CH+
and count the flash pulses of the red indicator
lamp. The digit “0” does not generate any flash pulse.
5. For the second code digit, press key
CH-
and count the flash pulses of the red indicator lamp.
6. For the third code digit, press key
VOL+
and count the flash pulses of the red indicator lamp.
7. For the fourth code digit, press key
VOL-
and count the flash pulses of the red indicator lamp.
The red indicator lamp turns off after the last flash.
Problems and Troubleshooting see on page 17.
