519065
24
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
h. Do not move or change the distance between the two remotes while learning all the required
keys for that Mode.
i. Do not attempt to learn directly under an incandescent or low-energy light as these can cause
interference with the IR transmissions. Keep at least one metre away from any such light
sources.
j. Avoid learning the Volume/Mute keys on your original remote unless you are sure these
operate the same target device e.g. some original DVD remotes also include TV Volume/Mute
key control – these can be two different types of code.
k. Avoid learning the VCR keys on your original remote unless you are sure these operate the
same target device e.g. some original TV remotes also include VCR key control – these can
be two different types of code.
l. Learning a key can take up to 3 seconds. Do not release the key being learned until the
“FERTIG” or “LERNEN FEHL.” screens have been displayed.
m.
If learning the first or second keys for a Mode results in continuous errors then try the following:
i. End the Learn session by pressing the Exit key.
ii. Clear out the learned commands for that Mode.
iii. Check the IR LEDs are correctly aligned between the two remotes.
iv. Adjust the distance between the two remotes to be closer (e.g. 15mm) or further away
(e.g. 50mm) from each other.
v. Try learning the original remote for that Mode again.
If the problem occurs again with the same key check the original remote key being learned –
does it transmit? Does it operate the target device? Try learning that key under a different
clear Mode. If it learns okay then it is likely to be a different code type from the others and
cannot be learned under the same Mode.
Notes:
1. You cannot learn under the Setup key.
2. All learned commands for a Mode are deleted if the same or a new 4-digit code is entered for
that Mode (includes Direct Code Entry, Code Search and Brand Search entries).
3. The Backlighting is turned off for Learning.
To Learn Commands:
a.
Press and hold Setup key until “CODE SETUP” is displayed (takes approximately 2-3 seconds).
b. Release Setup key.
c. Navigate to “LERNEN SETUP” by pressing the Setup key 3 times. Press and release OK key.
d. “LERNEN MODUS” is displayed. Press and release OK key.
e.
“QUELLENTASTE” is displayed. Press and release the desired Mode key (TV, VCR, DVD, etc.).
f. “LERNEN: TASTE“ is displayed. Press and release the LCD remote key to be taught with
original remote code.
g. “ORIG.-FB-TASTE” is displayed. Press and hold original remote key until the “FERTIG” or
“LERNEN FEHL.” screens have been displayed (see Tips on Learning) followed by the
“LERNEN MEHR?” screen (this process can take up to 2 or 3 seconds to complete). Release
the original remote key.
i. “LERNEN MEHR?” screen is still displayed. To learn more keys, press and release the OK key
and repeat from step “f”. To exit at this point, press and release the Exit key.
j. “WARTEN…” will be displayed briefly and the remote will exit Setup and return to normal
operation.
To clear Learn Commands
To Clear all stored Learned Commands under a Mode:
a.
Press and hold Setup key until “CODE SETUP” is displayed (takes approximately 2-3 seconds).
b. Release Setup key.
c. Navigate to “LERNEN SETUP”. Press and release OK key. “LERNEN MODUS” is displayed.
d. Navigate to “LOESCHEN MODUS”. Press and release OK key.
e.
“QUELLENTASTE” is displayed. Press and release the desired Mode key (TV, VCR, DVD, etc.).
f. “LOESCHEN BEST.” is displayed. Press and release OK key.
g. “WARTEN…” will be displayed briefly and the remote will exit Setup and return to normal
operation.
To Clear all stored Learned Commands (recommended on first time Learning):
a.
Press and hold Setup key until “CODE SETUP” is displayed (takes approximately 2-3 seconds).
b. Release Setup key.
c. Navigate to “LERNEN SETUP”. Press and release OK key. “LERNEN MODUS” is displayed.
d. Navigate to “LOESCHEN ALLES”. Press and release OK key.
e. “LOESCHEN BEST.” is displayed. Press and release OK key.
f. “WARTEN…” will be displayed briefly, then “FERTIG” and the remote will exit Setup and return
to normal operation
24
55415 BedienAnltg TeFu_Zweite Version 08.12.09 16:33 Seite 24
24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Telefunken TRC 850 - 8in1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Telefunken TRC 850 - 8in1

Telefunken TRC 850 - 8in1 Bedienungsanleitung - Englisch - 16 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info