Bedienungsanleitung Telefunken TX151 (Seite 73 von 75) (Französisch)

486215

Zoom out

Zoom in

Vorherige Seite

1/75

Nächste Seite

TX Bluetooth Guide 73

5. Press and HOLD PAGE on the base. The handset display will show Registering…. The

handset will return to standby mode if registration is successful.

Note:

If the base is found and the PIN is correct, an unused handset number will be assigned

automatically.

If the PIN is incorrect, “INCORRECT PIN!” will display with an error tone, you will need to re-

enter the correct PIN. If the base is not found, “NO BASE FOUND” will display.

De-register a handset

1. In standby mode, press MENU/OK then UP/DOWN to select Settings.

2. Press MENU/OK then UP/DOWN to select De-register.

3. Press MENU/OK then enter the system PIN. (Default is 0000.)

4. Press MENU/OK then UP/DOWN to select the desired handset.

5. Press MENU/OK. The display will show De-register?

6. Press MENU/OK to confirm. Display will show De-registered if it is successful.

Note: You cannot de-register the handset currently use in your hand.

You cannot de-register a handset if any other system handset is in use.

9 HELP

I cannot pair my mobile phone to the telephone base

- Make sure the Bluetooth function of your Bluetooth enabled mobile phone is turned on.

- See your mobile phone User’s Manual for more information.

- Make sure the cordless handset, corded base and mobile phone are located near each other.

- Remove the TELEFUNKEN TX 1** from your mobile phone’s Bluetooth device history list

(see your mobile phone User’s Manual for more information).

- Carefully follow the pairing instructions in the User’s Guide, making sure that your mobile

phone is not connected to any other Bluetooth device(s).

- Turn off your mobile phone, and then turn it on again.

- Reset the telephone base. Unplug the unit’s electrical power.

Wait for approximately 15 seconds, and then plug it back in. Repeat the above suggestions

Phone does not work

- Have you installed the battery pack correctly?

- Check that the mains power is correctly connected.

No dial tone

- Is the telephone cord of the base plugged into the phone socket?

- Check that the mains power is switched on at the power point.

- Only use the telephone cord supplied with the phone.

- The telephone line cord might be malfunctioning. Install a new telephone line cord.

- Move the handset closer to the telephone base. It might be out of range.

- Disconnect the telephone base from the telephone wall socket and connect a different

telephone. If there is no dial tone on this telephone either, the problem is in your wiring or local

service. Contact your local telephone company.

Cannot dial out or receive calls

- Check that the mains power is correctly connected.

- The battery may need recharging.

- Has there been a power cut? If so, place the handset back on the base for 10 seconds and try

again. If it still does not work disconnect the battery pack and mains power for 10 minutes, then

reconnect and try again.

You have a dial tone, but the phone will not dial out

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Telefunken TX151 Seite 73

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Telefunken TX151

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info