Bedienungsanleitung Telwin DRIVE 13000 (Seite 4 von 68) (Alle Sprachen)

649696

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

- 4 -

A-15. ON/OFF switch for the charge level, the output ports (ref.

A-11 and 12) and the LED lights.

A-16. Internal battery charge status indicator LED.

3. INSTALLATION

POSITIONING THE STARTER

When using the starter, position it on a horizontal, at and stable

surface.

4. OPERATING INFORMATION

4.1 How to use the starter:

WARNING: follow these instructions

meticulously,andalwaysintheordergivenbelow!

Alwayspreventtheblackandredclampsfromtouchingeach

other or a common cable!

- Make sure that the vehicle or boat to be started is switched off

(switch or ignition key in the OFF position).

- Connect the red clamp POS. (+) to the battery terminal POS. (+),

then connect the black clamp NEG. (-) to the vehicle chassis or

the battery terminal NEG. (-).

WARNING: failure to follow these rules may

compromisetheoperatinglifeofthedevice:

- Turn thevehicle ignitionto thestart positionforno more

than 3 seconds.

- Ifthevehicleorboatdoesnotstart,waitatleast15seconds

before trying again.

- If the vehicle or boat still does not start, wait at least 2

minutes before trying again.

After a successful start, with the engine running, follow the

sequence of instructions below with great care:

- Disconnect the black clamp (negative) from the vehicle.

- Disconnect the red clamp (positive) from the vehicle.

- Remove the starter cable connector from the starter

- Replace the cables and the starter in their seats inside the case.

It is highly recommended to recharge the starter as soon as

possible.

4.2Usingthestarterasapowerand/orchargingdevice:

- Select the output cable (g. A-4 or g. A-6) with the terminal

suitable for the device to be powered (g. A-7) according to the

required voltage/current;

- Insert the cable terminal into the appropriate output port on the

starter (g. A-10, 11, 12);

- Press the ON button seen in gure A-15

- Insert the other cable terminal into the device to be powered;

4.3 Using the LED lights

- Press and hold the ON button (g. A-15) for a few seconds to

enable the continuous LED light function.

The press the button in the following sequence:

- once to start the blinking light;

- twice to start the emergency signal;

- three times to switch the light OFF.

5.CHARGING

Important!Toachievemaximumbatteryperformance,always

chargebeforeuse,thenaftereverytimeitisusedand,inany

case,atleastevery3months.

The unit can be charged using a 230VAC power supply (using the

power supply adapter supplied, g. A-8) or using a 12V cable with

a jack plug (g. A-5).

Press the button seen in g. A-15 to check whether the battery

needs charging.

The LEDs seen in g. A-16 indicate the charge status of the battery,

which light up as the status increases:

- one LED only: low battery;

- all LEDs are on: fully charged battery.

5.1Chargingwith100Vac-240Vac50/60Hzpowersupply

WARNING: Use the suppliedpowersupply adapter

only!

- Insert the power supply adapter plug (Fig. A-8) into a 230Vac

socket or other compatible with the network voltage.

- Now insert the relative output plug into the charger socket seen

in g. A-9.

- The LEDs seen in g. A-16 light up in sequence when the unit is

charging and remain on when the unit is fully charged.

- The starter is tted with a control device to prevent overcharging

the battery and power unit. Leave the system to charge for as

long as necessary.

5.2Chargingonboardthevehicleusing12Vdcpowersupply:

- Insert the jack plug on the supplied cable (Fig. A-5) into the

cigarette lighter socket in the car or onboard the boat.

- Insert the other terminal of the supplied cable into the starter

charge socket (Fig. A-9).

6.DISPOSINGOFTHEBATTERY

When the starter battery is completely run down it should be sent

to a re-cycling facility. In some countries this is mandatory. Contact

the local special refuse authority for information on recycling.

WARNING:

Do not burn the battery to dispose of it. This could cause an

explosion. Before disposing of the battery, apply insulating tape to

the bare terminals to prevent shorting. Do not expose the battery to

intense heat or re as this could cause an explosion.

SPECIFICATIONS:

DRIVE9000

Type of battery:

- rechargeable factory-sealed lithium-polymer battery.

Battery capacity:

- 9000 mAh

Starter current (12 V):

- 350 A

- (600 A peak)

Starter cables:

- polarised terminals

- copper

- diameter 5.3 mm

(10AWG)

- length 250 mm

- PVC insulated

Light:

- LED

Output sockets:

- two USB 5V - 1A/2.1A sockets

- 12 V – 10 A socket

- 19 V – 3.5 A socket

Characteristics:

- ON/OFF switch

- automatic charging level reset switch

- charge level and fully charged indicator LEDs

- continuous, blinking and emergency LEDs

Weight:

- 640 g

Accessories included (g. A):

- Output power unit (g. A-8) 100 V-240 V 50/60 Hz, 12 VDC/1000

- charge cable with 12 V cigarette lighter jack plug

- Input/output connection cables (g. A-4, A-6)

- Various terminals (g. A-7)

DRIVE13000

Type of battery:

- rechargeable factory-sealed lithium-polymer battery.

Battery capacity:

- 12000 mAh

Starter current (12 V):

- 450 A

- (800 A peak)

Starter cables:

- polarised terminals

- copper

- diameter 5.3 mm

(10AWG)

- length 250 mm

- PVC insulated

Telwin DRIVE 13000 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info