627188

Telwin MAGNUM 400 CE Seite 6

6
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
- 6 -
- Fix the two welding cables as close to each other as possible.
- Operators must keep their heads and trunks as far away as
possible from the welding circuit.
- Operators must neverwind the weldingcables around their
body.
- Operators must never keep their body in the centre of the
welding circuit while they weld. Operators must keep both
cables on the same side of their body.
- Connect the welding current return cable to the piece to be
welded, as close as possible to the join being made/welding
spot.
- Never weld while remaining close to, sitting on or leaning
against the engine-driven welding machine (minimum
distance:50cm).
- Donotleaveferromagneticobjectsneartheweldingcircuit.
- Minimumdistanced=20cm(Fig.M)
- ClassAequipment:
Thisengine-drivenweldingmachinesatisestherequirements
oftheproducttechnicalstandardsforexclusiveuseinindustrial
environmentsforprofessionalpurposes.
ADDITIONAL PRECAUTIONS
- WELDINGOPERATIONS:
- Inenvironmentswithincreasedriskofelectricshock;
- Inconnedspaces;
- Inthepresenceofinammableorexplosivematerial;
MUST ALWAYS be evaluated in advance by an “Expert
supervisor”andmustalwaysbecarriedoutinthepresence
of other people trained in emergency procedures.
The technical protection means described in sections 7.10;
A.8;A.10.of“Part9:Installationanduse”ofthe“EN60974-9:
Apparatusforarcwelding”DirectiveMUSTALWAYSbeused.
-Welding should NEVER be allowed if the operator is above
oorlevel,unlessasafetyplatformisused.
- VOLTAGE BETWEEN THE ELECTRODE HOLDERS OR
TORCHES: when working with more than one welding
machine on a single piece, or on several pieces that are
connectedelectrically,dangerousno-loadvoltagesmaybuild
up between two different electrode holders or torches and
may reach double the allowed limit.
It is essential for an expert coordinator to use measuring
instruments to determine whether there is a risk, and to
be able to adopt adequate safety measures as indicated
in section 7.9 of theEN 60974-9:Apparatusfor arc welding
Directive.Part9:Installationanduse”.
RESIDUAL RISKS
- TOPPLING:positiontheengine-drivenweldingmachineona
horizontalsurfacethatissuitableforsupportingtheweight;
ifthesurfaceisnothorizontal(e.g.slopedorbrokenooring,
etc...) the welding machine can topple.
- IMPROPER USE: it is dangerous to use the engine-driven
welding machine for any purpose other than that for which it
is intended (e.g. defrosting piping from the water system).
- The only permitted way to lift the machine is described in the
“INSTALLATION”sectionofthishandbook.
2. INTRODUCTION AND GENERAL DESCRIPTION
Diesel engine-driven welding machine for MMA electrode welding in
DC direct current. Can be used with many different electrodes: rutile,
basic, cellulose, stainless, aluminium, cast iron, etc. It can be used as
a single-phase and three-phase AC generator for powering all types
of electric tool (e.g. sanders, drills, dowel drills, demolishers, etc.),
compressors, neon and incandescent lighting systems, etc.
ACCESSORIESSUPPLIEDONREQUEST:
- MMA welding kit
- Wheel kit.
3. TECHNICAL DATA
Data plate
The main data regarding engine-driven welding machine performance
and use are given briey in the characteristics plate with the following
meaning:
Fig. A
1- Serial number for engine-driven welding machine identication
(essential for servicing, requesting spare parts, searching for
product origin).
2- Symbol representing the internal structure of the engine-driven
welding machine, alternator.
3- U
0
: maximum loadless voltage.
4- A / A: indicates the welding current adjustment range (minimum-
maximum).
5- Welding circuit performance:
- I
2
: Currents that can be supplied by the welding machine
during welding.
- X : Intermittence ratio: indicates the time during which the
engine-driven welding machine can supply the corresponding
current (same column). Expressed in %, on the basis of a
10-minute cycle (e.g. 60% = 6 minutes work, 4 minutes rest;
and so on).
If the use factors (referred to a room temperature of 40°C)
are exceeded, the thermostatic safeguard cuts in (the
engine-driven welding machine remains in stand-by until its
temperature returns within the permitted limits).
6- Casing protection grade.
7- Sound power (or pressure) level guaranteed by the engine-
driven welding machine.
8- EUROPEAN Standard of reference for safety and for the
construction of arc welding machines.
9- Symbols that refer to safety regulations, the meanings of which
are given in chapter 1 “General safety regulations”.
10- Auxiliary power output:
- Nominal output voltage (V).
- Nominal output power 1ph (single-phase) and/or 3ph (three-
phase).
- Cosφ.
11- Nominal frequency.
12- Internal combustion engine characteristic data:
Note: The meaning of the symbols and gures given in the example
plate shown are indicative; the exact values of the technical data
of the engine-driven welding machine in your possession must be
looked for directly on the plate of the machine itself.
OTHERTECHNICALINFORMATION:
- ENGINE-DRIVENWELDINGMACHINE:seetable1(TAB.1)
- ELECTRODE-HOLDERCLAMP:seetable2(TAB.2)
The weight of the engine-driven welding machine is given in
table 1 (TAB.1)
4. ENGINE-DRIVEN WELDING MACHINE CONTROL,
ADJUSTMENT AND CONNECTION DEVICES
(See Annex)
5. INSTALLATION
WARNING! CARRY OUT ALL INSTALLATION AND
ELECTRIC CONNECTION OPERATIONS WITH THE ENGINE-
DRIVEN WELDING MACHINE RIGOROUSLY SWITCHED OFF.
THE ELECTRIC CONNECTIONS MUST ONLY BE CARRIED OUT
BY EXPERT OR QUALIFIED TECHNICIANS.
PREPARATION
Unpack the engine-driven welding machine and assemble the
separate parts included in the package.
Return cable-clamp assembly
Fig. B
Electrode-holder clamp-welding cable assembly
Fig. C
HOWTOLIFTTHEENGINE-DRIVENWELDINGMACHINE
The engine-driven welding machine MUST be lifted as shown in Fig.
D.
This is valid for both initial installation and for the entire life of the
engine-driven welding machine.
Note: The interconnection and power supply cables and piping must
… 6 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Telwin MAGNUM 400 CE wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info