Bedienungsanleitung Telwin PRO START 1712 (Seite 4 von 60) (Alle Sprachen)

649703

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

WARNING:DANGER!

Connect the mounting socket (Fig. A-1) to the starter’s

12V or 24V power supply, checking the voltage

required for the vehicle to be started, and only after

being absolutely certain that the clamps have been

connected to the battery polarities correctly.

- Connect the mounting socket following the instructions

above.

- Turn the ignition switch or key of the vehicle or boat to

ON. Wait about one minute. Turn the vehicle ignition

switch or key to the start position for no more than 5÷6

seconds. If the vehicle or boat does not start, wait at

least 3 minutes before trying again.

Warning: Do not allow the black and red

clamps to come into contact with each other

or to touch a common conductor.

- Whilst the engine is running, disconnect the mounting

socket from the starter and the clamps from the vehicle

in the exact order seen below:

1. the mounting socket.

2. the black (negative) clamp.

3. the red (positive) clamp.

- Return the clamps to their housing on the starter.

It is highly recommended to recharge the starter as

soon as possible!

Using the starter as a 12V power supply unit by

means of the cigar-lighter type socket (Fig. A-4).

WARNING!12VOUTPUTONLY!

In case of overload the re-settable safety

switch will trip. To restore operation, remove

the cause of overload and press the button shown

in Fig.A-2.

- Take the cover off the cigar-lighter type socket (Fig.

A-4).

- Insert the cigar-lighter plug of the device to be powered

into the socket (Fig. A-4).

Recharging using a 230V AC power supply

Important! To protect the battery and lengthen

its working life, charge it for 12 hours before

usingitforthersttime,thenaftereverytime

it is used and, in any case, at least every 3 months.

It is possible to recharge the unit using the 230V AC

power adapter supplied. We recommend keeping the

battery fully charged at all times. A low charge level could

shorten the life of the battery. Bear in mind that the time

needed to recharge the battery depends on the number

of times it has been used. It is possible to check whether

the battery level is low by pressing the red button (Fig.

A-5).

The voltmeter (Fig. A-3) will indicate the battery charge

level. The green area of the voltmeter indicates that the

battery is charged.

Recharging

1- Connect the free starter plug at POSITION 12V,

making sure that the starter clamps are positioned in

the relative pocket and insulated from each other.

2- Insert the car cigarette lighter plug supplied with the

battery charger into the starter outlet (Fig. A-4).

3- Insert the battery charger plug into a 230 V socket.

4- Allow the starter to recharge for as long as necessary

(refer to the battery charger user manual).

5- When charging is nished remove the battery

charger and disconnect the free starter plug from

POSITION 12V.

DISPOSING OF THE BATTERY

When the starter battery is completely run down it should

be taken to a re-cycling depot. In some countries this is

mandatory. Contact the local special refuse authority for

information on recycling.

WARNING: Do not burn the battery to dispose of it.

This could cause an explosion. Before disposing of the

battery, apply insulating tape to the bare terminals to

prevent shorting. Do not expose the battery to intense

heat or re as this could cause an explosion.

STARTER SPECIFICATIONS “4824”

Typeofbattery:

- rechargeable factory-sealed 12V acid-lead batteries.

Batterycapacity:

- 40Ah.

Outputcurrent@24V:

- 2200A peak current;

- 800A starter current.

Outputcurrent@12V:

- 4400A peak current;

- 1600A starter current.

Coppercables:

- PVC insulated 16mm

Cablelength:

- 190cm.

Outputsocket:

- 12V DC / max. current 10A.

Generalfeatures:

- re-settable safety switch for output overload;

- automatic charging level reset switch;

- “cigar-lighter” type socket, 12V DC.

Weight:

- 24kg.

Standardaccessories:

T-CHARGE 12 Power supply / Battery charger (Fig. B).

STARTER SPECIFICATIONS “6824”

Typeofbattery:

- rechargeable factory-sealed 12V acid-lead batteries.

Batterycapacity:

- 40Ah - 80Ah.

Outputcurrent@24V:

- 3000A peak current;

- 1000A starter current.

Outputcurrent@12V:

- 6000A peak current;

- 2000A starter current.

Coppercables:

- PVC insulated 25mm

Cablelength:

- 220cm.

Outputsocket:

- 12V DC / max. current 10A.

Generalfeatures:

- re-settable safety switch for output overload;

- automatic charging level reset switch;

- “cigar-lighter” type socket, 12V DC.

Weight:

- 39kg.

Standardaccessories:

T-CHARGE 12 Power supply / Battery charger (Fig. B).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Telwin PRO START 1712 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Telwin PRO START 1712

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info