627189

Telwin THUNDER 220 AC HONDA Seite 8

8
Zoom out
Zoom in
Vorherige Seite
1/108
Nächste Seite
- 8 -
- Connect the tool outlet to the input on the machine (Fig. B-7 or C-7,
C-8).
- Move the selector to position
230V 1~
(Fig. B-1) (200A AC
VERSION only).
WARNING!
- The load must be applied when the engine has been started.
- Disconnect the load before switching off the engine.
- If the AC outlets are overloaded or if the connected equipment
malfunctions, the thermostatic safeguards cut in (Fig. B-6 or C-6).
- Reset is not automatic. To reset the system (RESET) the
thermostatic safeguard MUST be re-activated.
- With the 200A AC version, the machine cannot be used as a
welding machine and a generator at the same time.
- With the 300A DC version it is advisable not to use the machine as
a welding machine and a generator at the same time (the output
voltage would not be constant).
Itisforbiddenanddangeroustoconnectthemachine
andpowertheelectricnetworkofabuilding.
8.MAINTENANCE
WARNING!BEFORECARRYINGOUTMAINTENANCE,
MAKE SURE THE ENGINE-DRIVEN WELDING MACHINE IS
SWITCHEDOFF.
ROUTINEMAINTENANCE
ROUTINE MAINTENANCE WORK CAN BE DONE BY THE
OPERATOR.
INTERNALCOMBUSTIONENGINEMAINTENANCE
Carryoutthechecksandprogrammedmaintenanceindicatedin
theUSERMANUALoftheinternalcombustionengineproducer.
EXTRAORDINARYMAINTENANCE
EXTRAORDINARY MAINTENANCE MUST ONLY BE CARRIED
OUT BYTECHNICIANSWHOARE EXPERT OR QUALIFIED IN
THE ELECTRIC-MECHANICALFIELD,AND IN FULL RESPECT
OFTHEIEC/EN60974-4TECHNICALDIRECTIVE.
WARNING!BEFOREREMOVINGTHEENGINE-DRIVEN
WELDINGMACHINEPANELSANDACCESSINGIT,MAKESURE
ITISSWITCHEDOFF.
Ifchecksarecarriedoutwhiletheinsideoftheengine-driven
weldingmachineislivethiscouldcauseseriouselectricshock
duetodirectcontactwithlivepartsand/orinjuryduetodirect
contactwithmovingparts.
- Make regular checks, at intervals that depend on the use and on
the amount of dust in the environment, inspecting the inside of the
engine-driven welding machine and removing any dust deposited
on the alternator and on the reactance coil using a jet of dry
compressed air (max. 10bar).
- Take the opportunity to make sure there are no loose electrical
connections and that the wiring insulation has not been damaged.
- After completing these operations, re-assemble the engine-driven
welding machine panels, fastening down the screws tightly.
- Never ever carry out welding operations if the engine-driven
welding machine is open.
- After having carried out maintenance or repairs, restore the
connections and wiring as they were before, making sure they do
not come into contact with moving parts or parts that can reach high
temperatures. Tie all the wires as they were before, being careful
to keep the high voltage connections of the primary transformer
separate from the low voltage ones of the secondary transformer.
Use all the original washers and screws when closing the casing.
- Periodically check the brushes for wear and position (300A DC
VERSION only).
9. ENGINE-DRIVEN WELDING MACHINE TRANSPORT AND
WINTERSTORAGE
Regarding engine-driven welding machine transport and winter
maintenance, refer to the USER MANUAL of the internal combustion
engine producer.
10.TROUBLESHOOTING
IF THE MACHINE IS NOT WORKING PROPERLY, BEFORE
MAKING MORE SYSTEMATIC CHECKS OR CALLING YOUR
SERVICING CENTRE MAKE THE FOLLOWING CHECKS:
- The welding current is suitable for the diameter and type of
electrode to be used.
- Make sure you have not exceeded the rated duty cycle; if the
thermal relay has triggered wait until the engine-driven welding
machine has cooled naturally, make sure the fan is working
properly.
- Make sure there is no shorting at engine-driven welding machine
output: in such a case eliminate the problem.
- Make sure the welding circuit connections have been made
correctly, in particular that the earth clamp is actually connected to
the piece, with no insulating material (e.g. paint) in the way.
Asfarastroubleshootingfortheengineisconcerned,referto
theUSERMANUALoftheinternalcombustionengineproducer.
Refertothenearestinternalcombustionengineretailershould
problemswiththeengineoccur.
I
MANUALEISTRUZIONE
ATTENZIONE! PRIMA DI UTILIZZARE LA MOTOSALDATRICE
LEGGERE ATTENTAMENTE IL MANUALE DI ISTRUZIONE
DELLA MOTOSALDATRICE E QUELLO DEL MOTORE A
SCOPPIO. NON FACENDOLO SI POTREBBERO CAUSARE
FERITEAPERSONEODANNIAIMPIANTI,APPARECCHIATURE
OALLAMOTOSALDATRICESTESSA.
MOTOSALDATRICI PER LA SALDATURA MMA PER USO
INDUSTRIALE E PROFESSIONALE.
Nota: Nel testo che segue verrà impiegato il termine “motosaldatrice”.
1.NORMEDISICUREZZAGENERALI
- Controllareilmotore primadiogniuso(vediilmanualedel
costruttoredelmotoreascoppio).
- Noncollocareoggettiinammabilivicinoalmotoreetenere
la motosaldatrice ad almeno 1 metro da edici e da altre
attrezzature.
- Non utilizzare la motosaldatrice in ambienti con pericolo
di esposione e/o incendio, in locali chiusi, in presenza di
liquidi,gas,polveri,vapori,acidiedelementiinammabilie/o
esplosivi.
- Rifornire il motore di carburante in un’area ben ventilata e
dafermo.Labenzinaèaltamenteinammabileepuòanche
esplodere.
- Nonriempiretroppoilserbatoiodelcarburante.Nelcollodel
serbatoio non ci deve essere carburante. Controllare che il
tapposiabenchiuso.
- Se si versa del carburante fuori del serbatoio, pulirlo bene
e permettere ai vapori di dissiparsi prima di accendere il
motore.
- Non fumare e non portare amme non protette nel luogo
doveilmotorevienerifornitodicarburanteolabenzinaviene
conservata.
- Non toccare il motore quando è caldo. Per evitare gravi
ustioni o incendi prima di traportare o immagazzinare la
motosaldatricelasciarecheilmotoresiraffreddi.
- I gas di scarico contengono monossido di carbonio, gas
velenosissimo,inodoreedincolore.Evitarnel’inalazione.Non
farfunzionarelamotosaldatriceinluoghichiusi.
… 8 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Telwin THUNDER 220 AC HONDA wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info