Bedienungsanleitung Tesla Model S (Seite 25 von 164) (Englisch)

615892

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

Seating Larger Children

If a child is too large to fit into a child safety

seat, but too small to safely fit into the

standard seat belts, use a booster seat

appropriate for the child’s age and size.

Carefully follow the manufacturer’s

instructions to secure the booster seat using

the seat belts. Do not use the LATCH system

to secure booster seats, even in situations

where the booster seat is equipped with the

LATCH system.

Installing Child Safety Seats

There are two general methods used to install

child safety seats:

• Seat belt retained - these seats are

secured using the vehicle’s seat belts (see

Installing Seat Belt Retained Child Seats

on page 25).

• LATCH retained - these seats can attach

to anchor bars built into the vehicle’s rear

seats (see Installing LATCH Child Seats on

page 26).

Check the child safety seat manufacturer’s

instructions and the table on Child Safety

Seats on page 23 to determine which

installation method to use. Some child safety

seats can be installed using either method.

Always follow the child safety seat

manufacturer’s instructions.

Installing Seat Belt Retained Child

Seats

First, make sure that the child falls into the

correct weight range for the seat.

Avoid dressing the child in bulky clothing and

do not place any objects between the child

and the restraint system.

Adjust harnesses for every child, every trip.

To securely hold child safety seats, all

passenger seating positions are equipped with

an automatic locking retractor (ALR) that, by

pulling the seat belt beyond the length

needed for a typical adult occupant, locks the

belt into place until the seat belt is unbuckled

and the webbing is fully retracted. The ALR

mechanism operates as a ratchet, winding in

slack and preventing the seat belt from

extending any further until it has been

completely rewound. When installing a child

safety seat, engage the belt's automatic

locking retractor by pulling the seat belt

webbing until it is fully extended. The ALR

system engages only when the seat belt is at

its maximum extension point.

Note: An automatic locking retractor

disengages only when the seat belt is

unbuckled and fully retracted. The belt can

then be worn as a normal belt, sliding freely in

and out and locking tight only in an

emergency. Once disengaged, the belt must

be fully extended to re-engage the locking

mechanism whenever you install a child safety

seat.

Always follow the detailed instructions

provided by the child safety seat

manufacturer. General guidelines are provided

below.

1. Place the child safety seat in Model S, and

fully extend the seat belt. Route and

buckle the seat belt in accordance with

the child safety seat manufacturer’s

instructions.

2. Allow the seat belt to retract, and remove

all slack in the seat belt while firmly

pushing the child safety seat into the

Model S seat.

3. If the seat belt retained child safety seat

has an upper tether, attach it to the back

of the seat (see Attaching Upper Tether

Straps on page 26).

Child Safety Seats

Seating and Safety Restraints 25

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Tesla Model S Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Tesla Model S

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info