Bedienungsanleitung Teufel Cinepaq 5100 (Seite 16 von 28) (Englisch)

704023

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

16 • CP 5100 DR

Special function buttons

Button “ Audio”

With the button 38 “Audio”, you can set the ambient

sound or the surround mode and the audio delay.

Setting ambient sound

Pushing the button 38 “Audio” brieﬂ y switches to the

respectively possible modes:

If only two speakers (front left and right) are active, you

switch the Dolby® Virtual Speaker (DVS) each time you

push the button:

“DVS REF” Normal DVS ambient sound.

“DVS WIDE” Extended DVS ambient sound.

“DVS OFF” Deactivate DVS.

If all speakers are active, two ProLogic and two stereo

settings are available for all dual-channel sources:

“PLII Movie” Dolby® ProLogic II for movies.

“PLII MUSIC” Dolby® ProLogic II for music.

“STEREO 5” Stereo playback on all speakers.

“STEREO 2” Stereo playback only on the front speakers

left and right and the subwoofer.

The surround mode is preset when Dolby Digital or DTS

coded multi-channel tracks are played back; as a result,

this function is blocked.

Setting audio delay

By pushing the button 38 “Audio” for more than two sec-

onds, you can set the value of the audio delay (see menu

function “Lip Sync” on page 13):

The current value in milliseconds (ms) is shown in the •

display panel and on the screen.

With the volume buttons • 37 “Volume +/–”, you can

now set the audio delay within the range from 0 to

240 ms.

The device deactivates the function after three seconds of

button inactivity.

Button “ Level”

You can set the sound with the button 45 “Level” and

adjust the volume of the speakers.

Adjusting the sound

By brieﬂ y pushing the button 45 “Level”, you access the

three ranges for the sound control in sequence:

Bass low tones (bass tones)

Treble high tones

Middle medium-range tones (language)

With the volume buttons 37 “Volume +/–” you can now

set the selected range from “–10” (decrease) to “+10”

(increase). After three seconds of button inactivity, the

device switches off the function.

Volume adjustment.

You can increase or decrease the relative volume for

each speaker. First push and hold the button 45 “Level”

for more than two seconds until the ﬁ rst speaker channel

is displayed in the display panel and on the top left of the

screen (see below). Tip the button 45 “Level” to select the

desired speaker now:

FRONT L – Front left

CENTER – Center

FRONT R – Front right

REAR L – Rear left

REAR R – Rear right

SUB – Subwoofer

With the volume buttons 37 “Volume +/–” you can now

set the volume within the range from “–10” to “+10”. After

three seconds of button inactivity, the device deactivates

the function.

Button “ Resolution”

By tipping the button 46 “Resolution” you can set the

resolution of the television set for HD playback. Possible

values:

HDMI 576P, HDMI 720P, HDMI 1080I, HDMI 1080P.

91341 GB 20100924.indd 1691341 GB 20100924.indd 16 24.09.2010 9:58:08 Uhr24.09.2010 9:58:08 Uhr

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Teufel Cinepaq 5100 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info