Bedienungsanleitung Teufel Concept C 200 (Seite 9 von 12) (Englisch)

562479

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

• Concept C 200 9

Split the cables down to approximately 30 mm on both

ends and strip approximately 10 mm of insulation on the

respective cores. Twist the cables so that no cores are

protruding.

Push down the lever for the connector terminal 12 on the

satellites and insert the stripped cable end into the open-

ing below the respective connector terminal. The cable is

clamped in place when the lever is released.

If you use banana plugs, screw the cord into place on

the plug (see instructions for the banana plug) and insert

the plug into the jack of the connector terminal 7 on the

subwoofer.

If you don’t use any banana plugs, turn the connector

terminal 7 counterclockwise. Insert the stripped cable end

into the hole that is now visible. Turn the terminal clock-

wise. This will clamp the cable in place.

Connecting the desktop remote control

Connect the desktop remote control to the jack

5 “REMOTE CONTROL”.

RCA input

You can connect almost any audio source to the RCA

jacks 4 “LINE IN” such as a computer, MP3 player

(with/without dock), video game system, television etc.

The source device only needs an output with line level.

Such outputs are conﬁgured either as stereo RCA jacks

or as a 3.5 mm jack plug. Connect such devices to the

jacks 4 “LINE IN” using a corresponding connector

cable. You can purchase such cables in our webshop

(www.teufelaudio.com) in the “Accessories” area.

USB input

Besides the RCA input, your Concept C 200 also has a

USB interface which you can use to connect to a note-

book, PC or Mac. Your Concept C 200 will operate just

like a sound card when connected via USB.

• Connect the terminal 6 USB with a free USB port on

your computer (all USB standards are supported).

A Type A to Type B USB cable is suitable.

A speciﬁc

driver installation is not necessary with Windows

ver-

sions XP, Vista, 7 and 8 and Mac OS X.

You may need to select your Concept C 200 as a play-

back device in the audio menu of your operating system.

It is displayed as “USB Multimedia Audio Device”.

Note:

In order to be able to use the analogue audio input 4

“LINE IN” and the Concept C 200 USB sound card at

the same time the computer must be switched on and

operational!

After connecting the USB cable to the “USB” terminal 6

and to the PC, the standard drivers will be installed.

Afterwards the following settings are required:

1. In the control panel please select the “Hardware and

Sound” area.

2. Then select the subitem “Sounds” and click “Manage

audio devices”.

3. In the pop-up window select “Speaker USB audio

device”.

You will now be able to select the item “Properties”

(previously greyed out). Please click this item.

4. In the “Speaker properties” window select the “Level”

tab.

You will now be able to activate the AUX IN input

for the Concept C by clicking the speaker icon in the

“Line” area.

Connecting to a power supply

9 8

• Ensure that the mains switch 8 “Power” has been

turned off (“0 OFF” setting).

• Connect the mains connector jack 9 with a power sup-

ply socket via the mains cord d.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Teufel Concept C 200 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info