Bedienungsanleitung Teufel DecoderStation 7 (Seite 18 von 20) (Englisch)

562467

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

18 • DecoderStation 7

Radio playback

Select one of the two radio modes as a source (see page

12):

FM – Reception of mono and stereo stations from 87.5 to

108 MHz. RDS mode possible.

AM – Reception of mono stations from 522 to 1.629 kHz.

Setting the radio stations

Direct entry of the tuning frequency:

• Tap the “FREQU.” 23 button so that the tuning frequen-

cy appears in the display panel.

• Enter the frequency without any decimal or comma

using the number buttons 22 “1 ... 0”.

• Push the select button 37 “•”.

Station search:

• Tap the “FREQU.” button 23 so that the tuning frequen-

cy appears in the display panel.

• Set the tuning frequency with the set buttons 27 “

◀/▶

”:

Manually: Every time the button is tipped, the fre-

quency is increased or decreased by one increment

(FM: 0.05 MHz, AM: 9 kHz).

Automatically: Holding down the button for a pro-

longed period of time starts station scanning in the

desired direction until a station with sufﬁciently strong

transmitting power is found.

The set frequency is displayed in the display panel. If the

station is received in stereo, the symbol “ ” will also ap-

pear. If the station transmits an RDS signal, the frequency

and the name of the station will alternate in the display

panel after a short time.

Stereo/Mono

Bothersome interference may occur for weak stereo

stations in the FM mode. In this case, you can switch

between mono and stereo reception with the “MODE”

button 29.

Station memory

The device can save up to 30 FM stations and 10 AM

stations. You can conveniently select the saved stations

with the push of a button.

Saving stations manually

• Set the desired station as described above.

• Push the “MEM” button 30.

The question “Store in P xx” will appear in the display

panel.

• With the number buttons 22 “1… 0”, enter the desired

memory slot number or select the desired number with

the arrow buttons 27 “

◀/▶

”.

• Push the select button 37 “•”.

• If the memory slot is already occupied, the question

“Overwrite?” will appear.

If you would like to select another memory slot, push

the “RETURN” button 28 and start from the beginning.

• Push the select button 37 “•” to save. The notice “OK”

will appear in the display panel brieﬂy.

The station has now been stored. The device will return to

normal operation after ﬁve seconds of button inactivity.

Selecting stations from the memory

You can select the occupied stations one after another

with the buttons 39 “CH +/–”.

Entry of the station memory slot number:

• Push the “PRESET” button 41.

The number of the last memory slot used will appear in

the display panel, e.g. “P03”.

• Enter the number of the desired memory slot (two dig-

its) with the number buttons 22 “1 … 0”.

• Push the select button 37 “•”.

Clearing station memory slots

• Access the station memory slot to be cleared (see

previous paragraph).

• Brieﬂy push the “MEM” button 30.

The question “Erase P xx?” will appear on the screen

and in the display panel.

• Push the “RETURN” button 28 to abort.

• Push the button 37 “•” to delete.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Teufel DecoderStation 7 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info