Bedienungsanleitung Teufel System 5 THX Select (Seite 3 von 4) (Englisch)

562423

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Attention

Risk of damage!

Improper assembly may result in damage.

• If mounting the speakers on the wall, make sure that the

installation is carried out expertly.

• Before drilling the holes, make sure that no pipes are

located within the drilling area using a metal detector.

• Only use suitable screws and dowels to mount the speak-

ers. Verify the carrying capacity of the walls.

• Hang the center speak-

er up on the wall using

the keyhole openings

on the speaker back

side and the screws you

previously mounted.

• You can also use these

openings for mounting

a wall holder. You can nd suitable products for this in our

web shop.

Removing the protective grids

The protective grids are

attached by pins and

sockets on the front of

the speaker and can be

easily removed. When

the protective grids are

removed, high frequen-

cy output becomes clearer in particular.

To remove the protective grids, reach behind them and slowly

pull them off to the front.

Attention

Risk of damage!

Make sure that you do not touch the highly sensi-

tive diaphragms.

Connecting

Danger

Danger of injury/damage!

Arrange the cables so that they do not pose a

trip hazard.

1. Pull the power plug of your amplier/AV receiver out or multi-

channel active subwoofer of the outlet.

2. Lay the speaker cables from your amplier/AV receiver or

multi-channel active subwoofer to each speaker. These

cables should be high-quality double-wire speaker cable with

marked strands.

3. A connector comprising two terminals is located on the

back side of each speaker, to which you have to connect the

speaker cables.

The terminal clips are each marked red (+) and black (-).

Make sure the polarity is correct!

Connect the like coloured terminals. Otherwise the

sound quality will suffer.

The speaker connections of your

amplier/

AV receiver or

multi-channel active subwoofer

should be marked similarly.

The strands of the speaker cables are marked with different

colours or shapes.

4. Split the single wire down to approx. 30 mm on both ends

and strip approx. 10 mm of insulation off of each cord.

5. Twist the stripped single wire ends together so that no wire

protrudes. Tin coating is not necessary.

6. Turn the connector terminal counterclockwise until loose.

Run the stripped cable end into the now visible hole. Close

the terminal by turning it clockwise. The cable has now been

clamped in place.

7. Connect the speaker cables to your amplier/AV receiver

multi-channel active subwoofer. The operating instructions of

the appliance should contain notes on this.

8. Reinsert the power plug of your amplier/AV receiver or

multi-channel active subwoofer into the outlet.

Crossover frequency

The ideal separation frequency for this speaker is 150 Hz. Set

this value on the amplier/AV receiver or DecoderStation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Teufel System 5 THX Select Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info