Bedienungsanleitung Teufel Theater 6 Hybrid (Seite 8 von 12) (Englisch)

562450

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

• Theater® 6 Hybrid

Danger

Danger of injury/damage!

Arrange the cables so that they do not pose a

trip hazard.

• Unplug the mains plug of your AV receiver from the

mains power supply so that it cannot be switched on

by accident.

Speakers

• Lay speaker cable from your AV receiver to each

speaker. Use a high-quality double wire speaker cable

with marked strands for this. The cable should have a

diameter of at least 2.5 mm

Little hint: label the cables at the receiver end – this will

help if you ever need to disconnect and reconnect the

receiver.

• On the back of each speaker is a connection terminal

with two clamps. Here you can connect the speaker

cables directly or using pin plugs. Direct connection

only is described here.

• For the two front speakers those are the jacks 1 “HIGH

LEVEL IN”.

• The terminals are each marked red (+) and black (–).

Make sure the polarity is correct!

Connect the like coloured terminals. Other-

wise the sound quality will suffer. The speaker

connections on your AV receiver should be similarly

marked. The strands of the speaker cables are marked

with different colours or shapes.

• Split the wire down by approx. 30 mm on both ends

and remove approx. 10 mm of insulation each. Twist the

wire so that no strands are protruding.

• Turn the connector terminal counterclockwise until

loose. Run the stripped cable end into the now visible

hole. Close the terminal by turning it counterclockwise.

The cable has now been clamped in place.

• Connect all the cables to the speakers in the same

way.

• Connect the other ends of the speaker cables to your

AV receiver. You should be able to ﬁnd corresponding

notes in the operating instructions of your device.

Subwoofer – audio connection

With the switch 7 “INPUT” you determine the connection

method for the integrated active subwoofer:

• “STEREO AMP” – the ampliﬁer doesn't feature a

subwoofer output and the subwoofer receives its signal

from connection “HIGH LEVEL IN”.

• “AV RECEIVER” – the ampliﬁer features a subwoofer

output and the subwoofer receives its signal via the

chinch connection “SUB IN”.

Connection via HIGH LEVEL IN

As the front speakers were connected in the previous sec-

tion already, you don't need another cable.

Connection via SUB IN

The subwoofers are connected to the subwoofer output

of the AV receiver using a mono chinch cable each (not

included in the product contents). If your AV receiver has

only one subwoofer output, you also need a Y chinch ca-

ble. Insert the chinch plugs in the jack 12 “SUB IN” each.

Subwoofer – mains power connection

• Ensure that the mains switch 4 “POWER” is set to

“OFF”.

• Using power cord d, connect the mains connection

jack 6 to a mains power socket.

• Also plug your AV receiver back into the mains power

supply.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Teufel Theater 6 Hybrid Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info