Bedienungsanleitung Teufel UL 40 C Mk2 (Seite 3 von 4) (Englisch)

703889

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

• Hang the center speaker on the wall using the keyholes and

the pre-installed screws.

• These openings are also suitable for mounting on a wall

bracket.

Alternatively, you can also use the threaded hole on the bot-

tom of the speaker. The speaker is delivered with a screw in

the threaded hole, which you must twist out before mounting

the speaker.

You can nd corresponding speaker stands and wall brack-

ets in our webshop.

Setup

• If you would like to set up the speaker,

afx the 4 enclosed rubber feet to the

corners on the bottom of the speaker.

This prevents noise created by vibra-

tions.

Connecting

Danger

Danger of injury/damage!

Arrange the cables so that they do not pose a

trip hazard.

• Pull the power plug for your AV receiver or multi-channel ac-

tive subwoofer out of the socket.

• Lay the speaker cable from your AV receiver or multi-channel

active subwoofer to the speaker. Use a high-quality double

wire speaker cable with marked strands for this. The cross-

section should amount to at least 1.5 .

• A connector terminal with two clips, which you have to

connect the speaker cable to, is located on the back of the

speaker.

• The terminals are each marked red (+) and black (–).

Make sure the polarity is correct!

Connect the like coloured terminals. The speaker

connectors of your AV receiver

or multi-channel ac-

tive subwoofer

should be marked similarly. The strands of the

speaker cables are marked with different colours or shapes.

1. Split the wire down by approx. 30 mm on both ends and

remove approx. 10 mm of insulation each.

2. Twist the stripped wire ends so that no strands are protrud-

ing. Tin coating is not necessary.

3. Turn the connector terminal counterclockwise until loose.

Run the stripped cable end into the now visible hole. Close

the terminal by turning it counterclockwise. The cable has

now been clamped in place.

4. Connect the speaker cable to your AV receiver or multi-chan-

nel active subwoofer. You should nd corresponding notes in

the operating instructions for your device.

Removing the protective grid

• You can remove the protective grids by carefully reaching

behind them and slowly pulling them out to the front.

• Removing the protective grid in particular will improve the

clarity of playback of high frequency sounds.

• When installing the protective grid, please make sure that

the installation pins slide directly into the corresponding

jacks on the speaker.

Crossover frequency

• We recommend a crossover frequency of 80–100 Hz. To the

extent possible, congure this setting on your AV receiver or

decoder station if they permit this particular setting.

• Operation in full-range mode is also possible (all speakers

are set to “Large”). However, the maximum volume is slightly

lower then.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Teufel UL 40 C Mk2 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info