Bedienungsanleitung Texas COMBI 800TGE (Seite 12 von 29) (Deutsch, Englisch, Dänisch, Französisch)

636684

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

Assembly

The machine is almost ready assembled from the

factory. Only a few items remain to be assembled:

Notice: The machine is prepared for assembling the

handlebar height in the middle position.

1. Install the lower handle on the machine using

the supplied bolts and tighten. See fig. 2-A.

2. Install the upper handlebar on the lower

handlebar using the supplied bolts.

See fig. 2-B (Do not tighten at this point)

3. Attach the dashboard to the upper handlebar

using the supplied bolts. See fig 2-C.

(Do not tighten at this point)

4. Tighten, the bolts at the upper handlebar on

the lower handlebar See fig.2-B.

5. Tighten the dashboard bolts. See fig. 2-C.

6. Attach the clutch handles and fix the cables:

Handle with arrows should be in left side.

Handle with broom should be in right side.

See figure 2-D.

7. Mount the gear rod

A. Mount the middle part of the lever fig.

3-A in the bottom of the gear rod fig. 3-B

(the short part which is fixed by a bolt

should point downwards) and turn it

approximately 2 rounds.

(note; anticlockwise). The arrow on the

gear rod should point towards the top of

the machine.

B. Put the gear selector in 4th gear.

C. Mount the middle part of the lever in the

gear selector and turn it until it locks.

D. Tighten the middle part by hand until it is

tightened in both ends.See fig. 3-C.

E. Loosen then the middle part 1 full round.

F. Tighten both of the nuts on the

gearlever.rod. See fig 2-B.

8. Mount the axle pole and wheels See fig 4.

Note: "Arrow" on the tire should be pointing

forward.

Check the tire pressure on both wheels before use.

Correct tire pressure is 20 psi/1.4 bar.

Use of machine with too low tire pressure,

can damage the tires!

Assembly of accessory

Follow the assembly procedure as shown in fig 5.

It is important that the accessory-unit is ”clicked” in

place by pressing down the foot pedal. See fig, 5-A.

Operation

Read the instruction manual for the engine,

before use.

Before using the machine, remove bigger objects from

the vicinity. Bigger objects can damage the machine.

Also check that all bolts are tightened.

Control always oil level before starting the

engine.

Start the engine:

1. Open the fuel tap.

2. On a cold engine open the choker.

Note: By a hot engine choke is not required.

3. Push the throttle handle to “Max” position.

Fig. 9-C

4. Pull the recoil starter gently until you feel

resistance in the rope. Then pull quickly and

energetic. Do not at any time let go of the

recoil starter but glide it gently back and pull

again.

5. Regulate the choker until the engine is running

smoothly.

Stop the engine:

1. Pull the throttle handle to “STOP” in order to

stop the engine. Fig. 9-C.

Remember to close the fuel valve if the machine will

not be used over a longer period !

Clutch Lever A - Forward and Reverse.

To operate the black clutch lever A in fig. 9, the control

stick must first be activated By tilting the control stick

to the right side and then activate the black handle, the

machine will move forward or backwards. To change

direction release the clutch lever and choose the

desired gear postion.

Gear: The machine has 4 forward and 1 reverse gear.

To change gear release the clutch lever fig. 6 A and

select the disered gear fig 9.

Gear R 1 2 3 4

Speed

2,3

Km/h

1,5

Km/h

2,9

Km/h

4,4

Km/h

5,8

Km/h

Always release the clutch handle before

changing gear!

Snowblower/Snowblade/Sweeper-accessory:

It is recommended only to use first gear in snow depth

from 10 cm and above. The snow clearing work

deteriorate at speeds above 1.5 km/h.

Pay attention while reversing. It is important that the

area is cleared, for any obstacle before reversing.

Never reverse the machine against a wall, tree or any

other fixed obstacle.

Clutch Lever B - Activation of accessory.

To operate the black brush lever B in fig. 9, the control

stick must first be activated. By tilting the red stick

completely to the right and then push the lever down

activates the accessory

Important! The red control stick on the clutch lever

must be pushed to the far right before the clutch lever

is activated. If not the clutch lever will forced of its hold.

If this happens, push the lever back up and repeat the

procedure. See fig. 9 A+B.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Texas COMBI 800TGE Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info