Bedienungsanleitung Texas Fusion 10B (Seite 16 von 32) (Deutsch, Englisch, Dänisch)

636688

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

from the rod (C) to lock the wheel assembly into

position.

Adjustment of depth skid

The depth skid can be set to 3 different depths. The

deeper it extends into the soil, the deeper the tilling

blades will work and the slower the machine will

advance. Setting the correct tilling depth will

significantly reduce the effort required. The depth skid

should always be adjusted to suit the ground conditions.

We recommend testing several depths to see which

works best.

Lubrication of gearbox

The gearbox is filled with gear oil at the factory.

Check oil level (the oil level should be visible for the

eyes

, when the oil cap is removed - Fig. 17) and fill up

with gear oil after the first 20 and 50 working hours.

Fill with gear oil type GL-5 / SAE 80W/90.

Do not overfill with oil.

For every 100 working hours, the gear oil must be

replaced. Remove the drain plug (Fig. 18) and let the oil

run out into a plastic tub or similar.

Tip: It is recommended to let the tiller blades rotate for

a while before draining the gearbox. It will make the

gear oil warm, so it runs out easier.

Fill with new gear oil (about 1.2 - 1.3 liter)

Starting and stopping the engine

Remember: Always check the oil level prior to use!

The oil level must reach the edge of the filling hole

(Fig. 21). Always use SAE-30 oil. Use only unleaded 95

octane gas. Never over-fill the gas tank.

Warning: Stay out of dashed zone, while starting the

engine!

Always start the engine from dotted operation zone See

red color in Fig. 20 .

Starting the engine

1. Set the throttle control on the handle to “4”

(Fig. 13B)

2. Open the fuel tap, if engine is fitted with this.

3. Position the choke at max.

The choke is not required if the motor is hot.

4. Pull the start cord to start the motor. Always feed

the start cord back into the motor by hand.

5. When the motor is started, set the choke to

minimum.

Stopping the engine

1. Set the throttle control to “1” and let the motor run

for approx. 30 seconds.

2. When the motor idles, set the throttle control to

“Stop”.

Vibrations may travel up into the handle

during use. We therefore recommend taking

a break every 2 hours.

Accessories overview

Severa

l accessory options are available for FUSION 10.

See Fig. 22 on page 5.

Texas recommend buying accessories, as it increases

the usage possibilities of the machine considerably.

Below accessories can be purchased for use with

FUSION 10 (the list is subject to local

changes/availabilities):

Tilbehør Nr.

Wheels: used to mount accessories, such as

rake.

Art. no. 91075500100

Digging claws: used if the soil is loose or

muddy and the machine is to be operated with

a ridge plough or harrow instead of wheels.

Art. no. 91075300100

Side discs: used for tilling in between crops,

such as carrots/potatoes, to avoid covering the

crops in soil. Side guards can also be used for

tilling along a wall or stone path, or in soft soil.

Art. no. 91075700100

Weight blocks: used to give the machine a

better grip when operating with a trailer or

snow blade.

Art. no. 91075400100

Rake: used to rake paths and entrances with

loose stones, for instance pebbles.

Art. no. 91062500100

Harrow: used to loosen the soil between crops

and thus remove weeds.

Art no. 91070000100

Weeder: used to loosen the soil and thus

remove weeds on paths and entrances.

Vare nr. 91061500100

Scarifier: used to aerate the lawn and remove

underlying dead grass from the lawn. The

grass grows greener and stronger, which

prevents the grown of moss.

Art. no. 91051550100

Potato plough: used for harvesting potatoes

Art. no. 91061200100

Trailer with seat: used for transport of various

materials.

Art. no. 91075000100

ssembly plate: used to attach front mounted

accessories.

Art. no. 91075600100

Snow blade: used to scrape snow from a solid

surface, such as paving slabs. Can be tilted to

the left/right. The assembly plate is necessary

for fitting.

Art. no. 92000160100 + 91075600100

Ridger: used to plough up ground for

potatoes, carrots and other root crops.

Art. no. 91076100100

Plough: used to turn the soil.

Art. no. 91076000100

Turning plough: used to turn the soil. Can be

rotated 180

Art. no. 91076200100

Rain-cover: used to protect the machine from

dirt or rain during storage.

Art. no. 40-11720

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Texas Fusion 10B Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info