Bedienungsanleitung Texas Hobby 380TGR (Seite 12 von 49) (Deutsch, Englisch, Dänisch, Französisch, Polnisch)

636703

Zoom out

Zoom in

Vorherige Seite

1/49

Nächste Seite

Maintenance and storage

The engine shall be stopped when carrying out

maintenance and cleaning operations, when changing tools

and when being transported by means other than under its

own power.

Check regularly that all bolts and nuts are tightened.

Retighten if necessary.

The engine must be completely cooled before storing

indoors or covered.

If the machine unused for a period of time, please refer to

the instructions in this manual.

Maintain or replace safety and instruction labels, as

necessary.

Only use original spare parts or accessories. If not original

parts or accessories is used, the liability is no longer

applied.

Replace faulty silencers.

Miscellaneous

The gears are delivered pre-greased. However, always

ensure they are well greased before each use.

The motor is not pre-filled with oil.

Factory-fitted control devices, such as the handle-mounted

clutch cable, must not be removed or exposed.

Only drain the fuel tank outdoors. Gasoline is extremely

flammable and the fumes are explosive.

Ensure that the machine is properly secured when

transported on a flatbed etc.

Reduce the throttle during engine shutdown and close the

fuel valve.

Assembly

Please follow the steps in figure:

(Actual model may vary from the illustration shown.)

Box content

A. Blades

B. Support wheel/ Depth skid

C. Tiller with cables

D. Upper handlebar

E. User manual

F. Lower handlebars, right & left

2. Mount support wheel. Remove bracket (A). The levers

on the bracket must go behind the rear axle.

3. Mount the two lower handlebars with the bolts supplied

(C). Note that the left and right handlebars are different.

Lower handlebar (A) must be mounted on the right.

Lower handlebar (B) must be mounted on the left.

4. Mount upper handlebar using the bolts supplied and the

hand wheel. Note: The arrows on the plastic brackets.

They must be aligned when mounting.

5. Mount throttle cable (A) and clutch cables (B) as shown

on the picture.

6. Mount the blades using the cotter bolts and pins.

Fill the motor with oil.

See changing the oil section for more details.

Clothing

When using the machine, wear close-fitting work clothes,

hard-wearing work gloves, ear defenders and non-slip boots

with steel toecaps.

Operating the tiller

Ensure the machine is placed on a level surface

with the support wheels lowered prior to start.

Remove all foreign objects from the work area

before using the machine. Stones, glass, branches

and similar items may damage the tiller. Also check

the bolts on the tiller are tightened.

Start the motor as per the instructions below. Stand

clear of the machine’s moving parts.

Never attempt to move the machine in any way

other than intended for normal use while the motor

is running.

The tiller is designed for use in vegetable gardens and

flowerbeds. Ensure that you are familiar with these

instructions before operating the machine, in particular the

motor start and stop procedures.

Fig 8: To use the black handle, the control stick must first be

activated. By tilting the control stick to the right or left side

and then activate the black handle, the tiller will move

forward.

Pay attention while reversing. It is important that the area is

cleared, for any obstacle before reversing. Never reverse the

tiller against a wall, tree or any other fixed obstacle.

Operation zone

While the machine is being operated and the motor is

running, do not leave the operation zone marked fig 9. If it is

necessary to leave the operation zone, for example to attach

an accessory, first stop the engine.

It is normally necessary to drive the tiller over a section of

earth 2-3 times from different directions. Do not till very wet

soil, as clods of earth will form that are difficult to break up.

Adjusting the handle

Fig 4.The handle angle can be adjusted. Use the two hand

wheels to set one of the 3 available positions. The handle

can be flipped forward during transport. NB: Ensure the

cables do not become trapped.

Adjusting the wheel/ depth skid

Fig 10.During operation, it may be necessary to raise the

wheel assembly, as it is connected to the depth skid.

Depress the pedal to the right of the support wheels to adjust

the wheel assembly/depth skid to one of the 3 available

positions.

The depth skid can be set to 3 different depths. The deeper it

extends into the soil, the deeper the tilling blades will work

and the slower the machine will advance. Setting the correct

tilling depth will significantly reduce the effort required. The

depth skid should always be adjusted to suit the ground

conditions. We recommend testing several depths to see

which works best.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Texas Hobby 380TGR Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info