Bedienungsanleitung Texas Instruments eZ430-Chronos (Seite 25 von 113) (Englisch)

514296

Zoom out

Zoom in

Vorherige Seite

1/113

Nächste Seite

www.ti.com

eZ430-Chronos Sports Watch Software

3.2.1.5 Heart Rate Mode - RF

(2)

Press "*" until the heart icon appears on the display that is heart rate mode is active (see Figure 3-1 for

details). When this mode is active, heart rate is shown and burned calories are determined (additional

settings must be made for first time use, see Section 3.2.2.7). For information on how to use the chest

belt, see to the documentation included with the heart-rate monitor device.

NOTE: This mode requires a heart-rate monitor (chest belt) that is not included in this kit, but

available from BM innovations, Germany (see www.bm-innovations.com/chronos). However,

a heart rate can be simulated without a chest belt by the eZ430-Chronos Control Center, see

Section 3.3 for details.

While almost all other eZ430-Chronos functions are based on TI's SimpliciTI protocol, the

heart-rate monitoring uses BlueRobin, an ultra-low-power low-data-rate wireless

communication protocol from BM innovations.

Secondary function: Heart rate display on/off. Press "UP" to enable/disable the heart-rate monitoring.

Once a connection is established, the heart rate is shown on the top LCD line

Set function: None

3.2.1.6 Speed Mode - RF

(3)

Press "*" until the "mi/h" or "km/h" icon is shown on the display; that is, the speed mode is active (see

Figure 3-1). Your running speed is shown on the LCD top line.

NOTE: This mode requires a heart-rate monitor (chest belt) which includes an accelerometer to

determine running speed. Visit BM innovations at www.bm-innovations.com/chronos for

available additions. However, speed can be simulated without a chest belt by the

eZ430-Chronos Control Center, see Section 3.3.4 for details.

While almost all other eZ430-Chronos functions are based on TI's SimpliciTI protocol, the

speed mode uses BlueRobin, an ultra-low-power low-data-rate wireless communication

protocol from BM innovations.

Secondary function: None

Set function: None

3.2.1.7 Tilt Mode

Press "*" until the tilt mode is active (see Figure 3-1). The acceleration is shown in G (9.81 m/s

) for all

three axes. After entering the tilt mode, the y-axis acceleration is shown by default, and the z-axis or

x-axis can be selected. Positive acceleration values are marked with a small arrow pointing up in the top

LCD line, left of the acceleration. Negative acceleration values are marked with a small arrow pointing

down. After 60 minutes, a timeout deactivates the measurements.

Secondary function: Select axis. The default is y-axis, followed by z-axis and x-axis.

Set function: None

(2)

Additional accessory or eZ430-Chronos Control Center heart rate simulation required.

(3)

Additional accessory or eZ430-Chronos Control Center heart rate simulation required.

SLAU292D–November 2009–Revised March 2011 eZ430-Chronos Software

Submit Documentation Feedback

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Texas Instruments eZ430-Chronos Seite 25

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info