Bedienungsanleitung Texas Razor 5160 TRWE (Seite 14 von 62) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Polnisch)

636639

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

Maintenance and storage

The engine shall be stopped when carrying out

maintenance and cleaning operations, when

changing tools and when being transported by

means other than under its own power.

Check regularly that all bolts and nuts are

tightened. Retighten if necessary.

The engine must be completely cooled before

storing indoors or covered.

If the machine unused for a period of time, please

refer to the instructions in this manual.

Maintain or replace safety and instruction labels, as

necessary.

Only use orginal spare parts or accessories. If not

orginal parts or accessories is used, the liablility is

no longer applied.

Miscellaneous

The motor is not pre-filled with oil.

Always before start check the engine oil level.

Factory-fitted control devices, such as the handle-

mounted clutch cable, must not be removed or

exposed.

Only drain the fuel tank outdoors. Gasoline is

extremely flammable and the fumes are explosive.

Ensure that the machine is properly secured when

transported on a flatbed etc.

Waste electrical products must not be

disposed of with the household waste. This

tool should be taken to your local recycling

centre for safe treatment.

The lawnmower is manufactured according to the latest

safety requirements. These include a blade brake that

stops the motor and blade in 3 seconds when the blade

brake. Every precaution is only effective when it is

followed exactly. Use the following description when

you mount your lawnmower.

Identification of the parts

See Illustration ID

Notice: the illustrations may vary from your present

model

A. Handlebar for drive

B. Handlebar for engine brake

C. Recoil starter

D. Wing nut

E. Rear discharge guard with spacer blocks

F. Water nozzle

G. Grass collector

H. Gasoline filling cap

I. Air Filter

J. Exhaust

K. Spark plug

L. Oil cap

M. Mulching plug

N. Throttle lever - Speed lever *

O. Choke*

P. Height adjustment*

Q. Side discharge guard*

R. Primer*

S. Breastplate*

T. Electric starter*

* may vary from your actual model.

Mounting

Unpacking: Illustration M1

Remove the mower from the box by pulling the machine

out form the side. The box contains:

1 pcs mower

4 pcs wing nut set consisting of wing nuts, bolts

and washers. (See ID; D)

2 pcs spacer blocks (See ID; E)

Warning: Ensure that cables are not pinched.

Handlebar and height adjustment: Illustration M2

The handlebars are height adjustable. This means that

they can be adjusted so that it best fits you. Before you

install the handlebar, it may be a good idea to have

decided which height is best for you.

1. Set the lower handlebar tube to the working height

that suits you. “H” is high position and the “L” is low

position.

2. Attach the wing nut from the inside of the side

bracket and into the lower handlebar.

3. Attach the upper handlebar on the lower. Fasten

with wing nut from the inside of the handlebar.

4. Customize cable and secure with cable clamps

Mounting the engine brake cable: Illustration M3

1. Gently push the top handlebar ID:B forward

2. Insert the engine brake cable from the outside, into

the hole in the bracket on handlebar ID:B and lock.

Mounting the drive cable: Illustration M3

1. Gently push the lower handlebar ID:A downward

2. Insert the drive cable from the inside, into the hole

in the bracket on handlebar ID:A and lock.

Mounting the recoil-starter: Illustration M4

1. Pull the engine brake handlebar and hold, in order

to release the starter cord on the engine.

2. Pull gently the starter cord from the engine

(Engine brake handlebar MUST be hold)

3. Attach the starter grip on the rack of handlebar.

4. Release the engine brake handlebar and the

starter grip.

Mounting the breastplate: illustration M5*

1. For models with breastplate with cup holder follow

illustration M5-1

2. For models with breastplate follow illustration M5-2

*Note: Not all models do have breastplate

Mounting the grass collector: Illustration M6

1. Click the frame to the grass collector.

The grass collector comes with a handy indicator

showing whether the box is full of grass and needs

emptying.

Rear discharge guard: Illustration M7-1

If you want to mow without grass collector it is important

to attach the two spacer blocks.

1. Insert the 2 blocks (ID:E) under the rear discharge

guard.

Note: The spacer blocks are for rear ejection only!

Otherwise they should be removed.

Warning: If the two blocks are not mounted. The

mower will have difficulties to dispose the grass.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Texas Razor 5160 TRWE Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info