Bedienungsanleitung Texas ST1300 (Seite 14 von 35) (Deutsch, Englisch, Dänisch, Finnisch)

636771

Zoom out

Zoom in

Vorherige Seite

1/35

Nächste Seite

Maintenance and Storage

Before carrying out any maintenance operations, cut off the electric power supply by disconnecting

the plug from the extension cable.

 Regular cleaning and maintenance of your appliance will ensure efficiency and prolong the life of your appliance.

 After each operation, take apart and clean out the ice and debris from the ventilator and its slot, auger and

housings.

 Only use a cloth soaked with hot water and a soft brush to clean the application. Never wet or spray water on the

machine!

 Do not use detergents or solvents as these could cause irreparable damage to your appliance. Chemicals can

destroy the plastic parts.

 To protect the application from corrosion when storing for a longer period, treat the metal parts with harmless oil to

the environment.

 Store the appliance in a dry room out reach of kids.

Change of belt (Fig. 7, 8)

The drive belts (34) and (35) need to be replaced depends on wear and tear.

Drive belt (35)

 Undo screws and take off the cover (39).

 Remove screw, washer and pulley frame (38), and the belt (35) from the pulleys.

 Install the new belt in the same pathway as the old one. Drive belt (34), small

 Loosen the nut and take the pulley (24) off with the belt (34) off the shaft.

 Remove the retaining ring (21), washer and pulley (33) if necessary.

 Reinstall belt (35), pulley frame (38) and the cover.

Auger (Fig. 9)

Caution! Check fasteners before each operation. Loosen auger result extra vibration and damage to the appliance.

To change the auger:

 Remove cover (39), pulley frame (38) and belt (35).

 Loosen the nut from other side of auger (42) and dismount the pulley (37) and auger axle (41).

 Replace the auger with a new one.

Scraper blade (Fig. 10)

Scraper blade is a wear item and should be replaced when necessary. Wear scraper blade invite extremely vibration and

damage of auger.

 Undo 3 screws.

 Replace with a new one.

Troubleshooting

Warning! Before any maintenance work, first switch off the appliance and unplug from the mains.

 Motor does not start

Mains failure. Check the mains if the same as described in the technical data.

Connections problem. Check electrical connection and make sure the operation of the switch is turned on

correctly.

 Poor snow throws

Drive belt worn or damaged. Replace the drive belt.

Auguer worn or damaged. Replace the auguer, check the tighten of screws and nuts.

Blocked discharge. Switch off the appliance and clean the discharge.

 Abnormal vibrations

Drive belt worn or damaged. Replace the drive belt.

Auguer worn or damaged. Replace the auguer, check the tighten of screws and nuts.

Scarper blade worn or damaged. Replace the scarper blade, check the tighten of screws.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Texas ST1300 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info