Bedienungsanleitung Texas TX602R (Seite 11 von 44) (Deutsch, Englisch, Dänisch, Französisch, Polnisch)

636693

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Operation zone

While the machine is being operated and the motor is

running, do not leave the operation zone marked fig 11. If it

is necessary to leave the operation zone, for example to

attach an accessory, first stop the engine.

It is normally necessary to drive the tiller over a section of

earth 2-3 times from different directions. Do not till very wet

soil, as clods of earth will form that are difficult to break up.

Adjusting the handle

TX602 model only: Fig 3.The handle angle can be adjusted.

Use the two hand wheels to set one of the 3 available

positions. The handle can be flipped forward during

transport. NB: Ensure the cables do not become trapped.

Adjusting the wheel/ depth skid

Fig 12.During operation, it may be necessary to raise the

wheel assembly, as it is connected to the depth skid.

Depress the pedal to the right of the support wheels to adjust

the wheel assembly/depth skid to one of the 3 available

positions.

The depth skid can be set to 3 different depths. The deeper it

extends into the soil, the deeper the tilling blades will work

and the slower the machine will advance. Setting the correct

tilling depth will significantly reduce the effort required. The

depth skid should always be adjusted to suit the ground

conditions. We recommend testing several depths to see

which works best.

Lubrication of gearbox

The gearbox is permanently lubricated at the factory, never

open the gearbox.

Starting and stopping the engine

Remember: Always check the oil level prior to use!

The oil level must always be between the min. and max.

Mark on the dipstick. Always use SAE-30 oil. Use only

unleaded 95 octane gas. Never over-fill the gas tank.

Warning: Stay out of dashed zone, while starting the engine!

Always start the engine from dotted operation zone See

Figure 9.

Starting the engine See fig. 10

1. Set the throttle control on the handle to max.

2. Position the choke at max. Move the choke lever fully to

the left. The choke is not required if the motor is hot.

3. Pull the start cord to start the motor. Always feed the

start cord back into the motor by hand.

4. When the motor is started, set the choke to minimum

(fully to the right) Engage the throttle slightly.

Stopping the engine

1. Set the throttle control to “low” and let the motor run for

approx. 30 seconds.

2. When the motor idles, set the throttle control to full stop.

Use the toolbox underneath the breastplate to keep tools

handy.Fig 8.

Vibrations may travel up into the handle during

use. We therefore recommend taking a break

every 2 hours.

Cleaning the tiller

The tiller should be cleaned after use. Use a garden hose to

wash off soil and dirt. Remove any grass, etc. from the rotor

shaft. The chassis number should only be cleaned with a

damp cloth to avoid unnecessary wear. Avoid using a high-

pressure washer during cleaning.

Changing the oil

The oil should initially be changed after the first 5 hours of

use, and thereafter once per year.

1. Let the motor run for 5 minutes to heat up the oil.

This allows the oil to run more freely and makes for

a more complete oil change.

2. After 5 minutes, stop the motor. Remove the spark

plug cap. Drain the oil by unscrewing the sump plug.

Remember to drain the oil into a container of

sufficient capacity. NB: The motor must not be

tipped backwards more than 45 degrees.

3. Screw the sump plug back in and pour new oil into

the motor. Do this by removing the dipstick and

pouring in the recommended quantity of oil.

4. Refit the spark plug cap.

Alternatively, use an oil extractor kit.

1. Suck the oil up through the oil filler hole using the

syringe. Use the hose to reach the sump.

2. Transfer the used oil to the container.

3. Fill the engine with new SAE-30 oil.

4. Check the oil level using the dipstick.

Remember to dispose of used oil in a safe way.

Oil and oil extractor kit are not included

Air filter maintenance

Please inspect and clean the air filter on a regular basis. If

the filter has not been cleaned for a longer period, this will

have influence on the engines power take-off and the

exhaustion.

1. Clean around the air filter before it is removed.

2. Carefully remove the paper filter and check it. Brush

it with a soft brush. If it is very dirty, it must be

changed. Take care that no dirt gets into the intake

of the engine.

3. Wash the black foam element on the right side in

warm soapy water.

4. Press the water out of the foam element and let it

dry. Put a few drops of SAE-30 oil on the filter to

moisten it lightly with oil. Carefully squeeze out any

surplus oil. Remount the element.

5. Check that all parts are fitted correctly and the cover

closed as shown in the picture.

Spark plug maintenance

• Remove the spark plug cap.

• Brush away any dirt and deposit of the spark plug.

• Loosen the spark plug using a spark plug socket.

• Check the insulation is intact.

• Clean the spark plug using a wire brush.

• Measure the electrode gap 0.7–0.8 mm. Avoid

damaging the electrode.

• If it is damaged, replace it with a new one.

• Refit the spark plug.

• Refit the spark plug cap.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Texas TX602R Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info