Bedienungsanleitung TFA 30.3000 (Seite 2 von 23) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

647511

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

Introduction

Congratulations on purchasing this remote-controlled Temperature Station with radio-controlled time.

The operation of this product is simple and straightforward but please read this instruction manual to

ensure that you have the full benefit of all its features.

Features of the Temperature Station

* Radio-Controlled (DCF-77) clock for ultimate time precision.

* Indoor temperature display with minimum and maximum temperatures memory. Indoor temperature

display range from -30.0°C to +70.0°C with 0.1° resolution.

* Outdoor temperature display with minimum and maximum temperature memory and time received

display. Outdoor temperature display range from -30.0°C to +70.0 °C with 0.1° resolution.

* Outdoor temperature trend indication.

* Wall mounting or table stand.

* Able to take up to 5 outdoor transmitters (optional)

Features of Temperature Transmitter

* Remotely transmits outdoor temperature at 433MHz to base Temperature Station.

* LCD display showing current temperature.

* Shower proof casing.

* Wall mounting case.

Getting Started

Please follow these steps to ensure that your new Temperature Station and Temperature Transmitter

work together correctly:

1. Remove both units from the packaging and place in front of you on a table.

2. Ensure the batteries you are going to insert into the units are of the correct sizes and are new.

3. First, insert the batteries into the Temperature Station. Once the batteries are in place, all segments of

the LCD will light up briefly and the indoor temperature will then be displayed.

4. Within 1 minute of activating the Temperature Station, place the two small batteries into the transmitter.

The temperature will then be displayed on the small LCD of the transmitter. If the temperature is not

displayed, remove the batteries and wait for at least 10 seconds before reinserting them.

5. After a few seconds of inserting the batteries into the transmitter, the Temperature Station will start

receiving transmissions from the transmitter. The remote temperature will then be displayed on the

Temperature Station. If this does not happen after 30 seconds, the batteries will need to be removed

from both units and reset from step 3.

6. The Temperature Station can take up to 5 remote transmitters. If you have bought additional transmitters,

follow step 4 for all extra transmitters. However, ensure that you leave one minute in between the

reception of the last transmitter and the set-up of the following transmitter. The Temperature Station

will number the transmitters in the order of set-up, i.e. the first transmitter will have the temperature

displayed with the number 1 against it and so on.

7. When all the transmitters are set up, there is a testing period, during which the display switches quickly

between all the received transmitters at random, according to which random transmission it receives.

Pressing any key will stop this process and the display will show the temperature for the first transmitter.

The process also stops automatically if no keys are pressed for a few minutes.

8. After the remote temperature has been received and displayed on the Temperature Station, the DCF

time code reception is automatically started. This takes typically between 3-5 minutes in good conditions.

This time period is an excellent opportunity to locate the Temperature Transmitter in a suitable position

outdoors, no more than 25 metres from where your Temperature Station will be finally positioned.

9. If after 10 minutes the DCF time has not been received, use the "SET" key to manually enter a time

initially. The clock will automatically attempt each hour to receive the DCF time and when successful

this will override any manually set time. Please refer to the sections on Radio-Controlled Time reception

and Manual Time setting in this manual for more details.

The Temperature Station

The Temperature Transmitter

Note:

* If more than one transmitter is used, keep the set-up time of all units within 8 minutes, otherwise start

up problems may occur as the Temperature Station may not attempt to receive any new 433 MHz

transmission signals after this period.

* If the Temperature Station is already set up and you wish to add extra transmitters, then the receiving

unit and all the transmitters need to be reset. To do this the batteries from all the units need to be

removed. Wait for at least 10 seconds before repeating the procedure above from step 1.

* When changing the batteries for any unit, then all the other units also need to be reset. As before, the

batteries from all the units need to be removed. Wait for at least 10 seconds before repeating the

procedure above from step 1.

Remember always to insert batteries into the Temperature Station first so as to be able to

distinguish the order of the transmitters and to avoid start up problems.

* When inserting batteries to all units, ensure that they do not spring free from the contacts, otherwise

start up problems may occur.

TIME

INNEN M A X

AUSSEN MI N

SET INNEN AUSSEN RESET

LCD

DISPLAY

BUTTONS

STAND

HANGING

HOLE

BATTERY

COVER

BATTERY

COVER

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

TFA 30.3000 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info