Bedienungsanleitung TFA Opus 35.1112 IT (Seite 10 von 31) (Englisch)

658128

Zoom out

Zoom in

Vorherige Seite

1/31

Nächste Seite

WIND SENSOR

The wind sensor must be installed with the front of the sensor (the solar panel)

facing true South, or the reported wind direction will not be accurate. Mount within the

50 meters wireless range of the thermo-hygro sensor and on the same side of the

house. The roof may or may not be an ideal mounting location. Secure the main unit to

the shaft of the mast holder. Use the right-angle adaptor if the wind sensor will be

mounted on a horizontal mast or surface.

Fasten the wind sensor to a suitable mast using the two U-bolts, washers and nuts

included. Note: Mount the wind sensor onto a mast so the wind can reach the sensor

unobstructed from all directions for an accurate reading. The ideal mast is between

15.75mm and 33mm in diameter. The wind sensor DOES NOT have replaceable

batteries, it consumes solar power and charges the internal battery pack automatically.

RAIN SENSOR

The rain sensor should be mounted on a level surface in an open area and bright area

within the 50 meters wireless range of the thermo-hygro sensor and on the same side

of the house. Mount the rain sensor at least 0.30 meter off the ground level for optimum

wireless transmission. The rain sensor should be accessible to allow for period cleaning

of debris or insects.

THERMO-HYGRO SENSOR

The thermo-hygro sensor is "weather resistant", but not "water proof". To ensure an

extended life of your sensor, mount it in a semi-covered place out of the elements. An

ideal location for the thermo-hygro sensor is under the eaves on the North side of the

house to avoid the effects of sunlight. Mount the sensor 0.5 meter down from the eaves

to ensure optimum performance. This way the weather data collected by the sensor will

not be affected by the temperature of the air coming out of the attic.

To wall mount the thermo-hygro sensor, fix the wall holder onto the desired wall using

the included screws, plug the sensor firmly into the wall holder and replace the rain

cover if it is not already in place. Note: After mounting the units, if the weather data is

not received, press and hold the ▲UP ARROW key for 2 seconds to synchronize the

wireless display to the sensors.

HEAVY WEATHER PC SOFTWARE

Use your PC to store and graph the latest weather data collected by the weather station.

Download the Heavy Weather PC software from www.tfa-dostmann.de

The Help function of the Heavy Weather Pro-Software contains detailed information

about handling and operating the software.

Note: Please pay attention about pc-connection:

It must be distinguished between “synchronize” and “contact”

“synchronize” = introduce the hardware to each other

“contact”= push the wireless connection for transfer of new data

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

TFA Opus 35.1112 IT Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von TFA Opus 35.1112 IT

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info