573457
11
Zoom out
Zoom in
Vorherige Seite
1/12
Nächste Seite
INSTRUCTIONS FOR USEINSTRUCTIONS FOR USE
Functions/Buttons Explained in Detail
General instructions for all six functions:
Plug the power cord into an outlet. A short beep will sound indicating that the unit is on.
Press the “ON/OFF” button. The unit will beep again and all six lights on the control panel will flash to indicate that the unit
is on and in STANDBY MODE. This will last for approximately 10 seconds (ten flashes).
If a function is not selected during this time, the “ON/OFF” button will have to be pressed again before selecting a function.
After all of the ingredients are added to the container, lock the lid into place (as shown in the “Assembly” section above)
and choose the appropriate function. Once one of the functions is chosen, the unit will beep once, which means the
selected cycle has started.
When the chosen cooking function is completed, the unit will stop automatically and will beep ten times while all six
indicator lights are flashing.
NOTE: If the indicator lights are flashing and the unit is beeping continuously during operation, it means that there is
an error with the operation or something else is wrong. If this happens, please refer to the Trouble-Shooting section of this
User’s Guide.
Pressing the “ON/OFF” button once at any time during any of the cycles can be used to stop that cycle and will
automatically put the unit into STANDBY MODE for about 10 seconds (flashing lights). Pressing the “ON/OFF” button
twice during any of the cycles will turn the power supply off. To turn the appliance back on, simply press the “ON/OFF”
button one more time and the lights will flash to signify that the unit is in STANDBY MODE again.
To remove the container, hold it by the handle and tilt it slightly forward (see diagram).
Attention! If the container contains hot liquid when being placed on, or removed from the base, please note
that a slight tilt may cause the hot liquid to leak out.
When removing a container containing liquids, always make sure to turn the unit off and unplug it from the power
supply.
Important Information about the Sensors
To ensure safety at all times, the FlavorFull™ System has a MINIMUM liquid sensor and a MAXIMUM hot liquid overflow
sensor inside the container, located at the base and the top of the handle, as well as a safety micro-switch cut-off (aka internal
sensor) on the motor base.
Always observe the appliance carefully when any of the functions are on. The sensors are very particular and will
only react in specific situations.
The MAXIMUM hot liquid overflow and MINIMUM liquid sensors will work if the liquid exceeds the the MAXIMUM hot liquid overflow
sensor, or if the water is less than the MINIMUM liquid sensor at the time of the functions is selected. Always make sure the total
volume of ingredients added is over the appropriate MIN mark, but not more than the appropriate MAX mark. The internal sensor
near the base of the container must be covered with liquid. Under-filling the container will result in the alarm sounding and the unit
failing to operate. However, should the boiling action during cooking cause the hot contents to reach the lid, the upper sensor will
switch off the heating function to help prevent boiling over.
The MAXIMUM hot liquid overflow sensor only reacts during the cooking functions. However, since there is no ‘hot liquid overflow’
concern during the “REHEAT” process, the hot liquid overflow sensor will not work during this process. Therefore, always make sure
to follow instructions regarding the MAX liquid markings.
For the non-cooking functions, “INFUSE/BLEND” (1) & “PULSE” (2), it is important that the ingredients are between the MINIMUM
and MAXIMUM marks. The MAXIMUM hot liquid overflow sensor does not react during these cycles so care must be taken to make
sure that too much liquid is not used. Also, it is NOT possible to blend/mix dry ingredients, as the internal and bottom sensors won’t
recognize them.
When using the “BOIL/STEAM” (3) function, the MINIMUM liquid sensor will not react if the water level drops below the MIN mark.
This is because the bottom sensor will be wet from condensation formed during the cycle and from the water level dropping. The
internal sensor will react but only once the liquid evaporates completely. The MINIMUM liquid sensor only reacts if a cycle is started
with too little liquid (below MIN mark).
1011
!
CAUTION
!
CAUTION
!
CAUTION
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Thane FlavorFull wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info