Bedienungsanleitung Thermex ERS serie (Seite 21 von 84) (Englisch, Italienisch, Spanisch, Polnisch)

782579

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

Replace the magnesium anode, clean the THE from the scale, if necessary, and remove the

sediment;

Perform the assembly, fill the EWH with water and switch on power supply.

When carrying out the EWH maintenance using the resources of a specialized organization, a

corresponding mark shall be made in the warranty certificate with the stamp of the organization

that carried out the maintenance. When the magnesium anode is replaced by the customer, a sales

receipt for the purchase of the magnesium anode shall be attached to this EWH manual.

Possible malfunctions and remedies

In case of malfunction in the product operation, it is necessary to disconnect it from the power supply

network and shut off the water supply.

Failure

The pressure of hot

water from the EWH

has decreased. Cold

water pressure has

not changed

Remedy

Remove the valve and rinse it

with water

Possible Reason

Clogging of the relief valve

inlet opening

Heating time has

increased

THE is covered with scale

crust

Remove the THE and descale it

The voltage in the power

supply network has decreased

Contact the organization

responsible for the maintenance

of the power supply network

The valve 24 (Fig.1) is not

closed or failed

Close or replace the valve

24 (Fig.1)

EWH works, but does

not heat water

Contact the service center

The mains cable is damaged

Disconnect the EWH from the

power supply network, remove

the protective cover, press the

thermal switch button until it is

secure, install the cover and

switch on the power supply (Fig. 2)

The thermoswitch was

triggered or is not switched on

Frequent triggering

of the thermal switch

The set temperature is close

to the temperature limit

Turn the thermostat knob toward

temperature decrease (–)

The thermostat tube

is covered with scale

Remove the removable flange

from the EWH and carefully

clean the pipe from scale

The powered EWH

does not heat water.

There is no backlight

of control lamps.

There is no voltage in the

power supply network

Contact the organization

responsible for the maintenance

of the power supply network

The residual current device

was triggered (if available)

Press the reset button of the

residual current device.

Check the voltage.

The powered EWH

does not heat water.

There is no backlight

of control lamps.

Fig. 2

Push

The abovementioned malfunctions are not defects of the EWH and shall be eliminated by the

customer themselves or by a specialized organization at the customer's expense.

Where impossible to eliminate the malfunction using the above recommendations or in case of any

other problems, contact the service center specified in the user manual.

Transportation and storage of electric water heaters

Electric water heaters shall be transported and stored in accordance with the handling symbols

shown on the package:

1. 2. 3. 4.

1. The need to protect the cargo from moisture;

2. Frailty of the cargo, condition of careful handling;

3. Recommended temperature range for cargo storage: from +10°С to +20°С;

4. Correct vertical position of the cargo;

20 21

ENEN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thermex ERS serie Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thermex ERS serie

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info