Bedienungsanleitung Thermocet Coventry S (Seite 18 von 26) (Englisch)

607253

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Page 18

15. Additional instructions for the Mertik Maxitrol GV60 and the remote control:

Ensure that the fuel supplied to the unit is clean and free from particles and moisture.

Before a gas supply pipe (new or existing) is connected to the main gas pipe at the gas meter and to the gas

control block of the unit, clean and dry compressed air should be blown through it. Cut copper pipes as well

as aluminium pilot pipes (diameter = 4 mm) must be deburred and blown clean before they are connected.

The dust filter at the connection to the gas control block will only filter out the coarsest dirt from the sys-

tem. Fine particles are still able to reach the inside and may damage and/or adversely affect regulation in

the gas control block.

Heat, moisture and dust are a threat to all electronic components

Install the electronic gas control only after all construction, plastering and paintwork has been completed. If

work such as this is unavoidably still being carried out, then protect the control box against dirt and mois-

ture penetration by using, for example, plastic film.

Select a location for the control box that is lower than the level of the main burner bed and outside

the radiation area (heat) of the burner.

Electronic components will become permanently faulty when they are exposed to temperatures that are

higher than 60°C. Normal AA batteries will crack open at temperatures >54°C and the battery contents will

damage the electronic switches below. Batteries last longest at <25°C. At >50°C the life span is around 23

weeks, this makes the use of the gas fire unnecessarily expensive.

Only install the gas control block and receiver as pre-installed at the factory

Remember that components may have to be replaced or that repairs may have to be carried out at a later

date.

This may be made more difficult if the control is installed using a method that is different from the one pre-

scribed by us.

Only add the batteries or connect the 220 V adaptor once all the wiring to the receiver, gas control

block and pilot set has been connected.

Premature connection to the energy source may damage the control’s CPU (central processor).

Ensure that the ignition cable is not near the antenna wire and that they do not cross each other.

The high voltage that is released at ignition may damage the sensitive receiver circuit.

This may mean that the unit may become less responsive or not respond at all to the handset commands.

Maintain 40mm mutual distance for this reason. (See photograph 1 on page 19)

Loosen the antenna wire from the terminals on the receiver box

Direct the antenna wire away from the ignition cable and in the direction of the control box door.

Ensure there is no contact with metal components. Ensure there is no damage to the connection to the elec-

tronic components or to the wire itself. (See photograph 1.)

Connect the wires correctly to the contact breaker behind the gas control block.

The shortest wire runs immediately back to the 1/0 switch and can be found nearest to the back of the gas

control block. The longest wire runs to one of the two connections on the receiver box and only fits on one

of the screws.

Do not tighten the contact breaker and the thermocouple connection too tightly on the gas control

block or to each other.

It is sufficient to tighten by hand and add a half a turn with an open-end spanner. Tightening too loosely

will break the connection to the magnetic coil below and/or the insulation around the aluminium contact pin

in the contact breaker.

This may lead to the magnetic coil not opening the gas supply to the pilot and the unit will not work.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thermocet Coventry S Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info