Bedienungsanleitung Thermocet Estilo (Seite 24 von 32) (Englisch)

607258

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Page 24

14. PROBLEMS AND POSSIBLE SOLUTIONS

Please first check if all guidelines were followed before attempting to solve any problems with the unit.

Warning:

Solving problems with your unit, whether gas related or electrical, must always be performed by a qualified

technician.

SYMPTOM ACTION TO BE TAKEN

The pilot flame will not

light. After repeated igni-

tion.

1. There is air in the pipes if you switch the unit on for the first time or after a ser-

vice. It will take a little while until all the air has flowed out of the pipes and gas

flows through that can be ignited. Ignite the pilot flame several times in order to

allow the air to escape.

2. See whether the gas pipe to the unit is open and if there is sufficient gas pressure

to the unit.

3. Check whether there are sparks between the spark electrode and the pilot. If

there are no sparks:

a) Check whether the connection between the electrode and the ignition is bro-

ken or faulty.

b) Check whether the spark short circuits at another point or jumps.

c) Check whether the electrode is broken.

The pilot flame will not re-

main alight after ignition.

1. Check whether the pilot flame is large enough to burn around the thermocouple.

If the flame is too small, you need to check the gas feed pressure. If the size of

the pilot flame cannot be adjusted, there may be an obstruction in the pilot.

2. Check whether the thermocouple interrupter is connected to the gas valve prop-

erly.

3. Check that the gas valve is not faulty.

4. Check whether the restriction plate has been placed according to instructions

(See page 22)

The main burner goes out

when the unit is warm.

1. This can be a normal effect of the thermostat.

Check whether the pilot flame is able to heat the thermocouple adequately. If the

pilot flame is too small then the gas pipe or the pilot flame adjustment need to be

checked.

2. Check whether the restriction plate has been placed according to instructions

(See page 22)

Soot deposits on the glass. 1. Check whether the lava split is lying on the burner in the correct manner.

2. Check if the pilot burner is free from burner filling.

3. Check whether there is any blockage in the burner openings

4. Check if the flue tube is functioning correctly and if the flue tube is not hindered

or blocked.

5. Check the pipe pressure.

Sharp blue flames that are

released by the burner or a

pilot that burns too wildly.

1. Check whether the restriction plate has been used.

Weak (stifling) pilot flame. 1. Check the pilot burner pressure or duct pathway

Main burner will not burn

after the pilot burner is

functioning.

1. Check if the motor button turns and whether the batteries are empty.

2. Possible defect in the gas block

3. Check whether the pilot flame ignites the burner well.

4. Check that the burner opening is not blocked.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thermocet Estilo Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info