Bedienungsanleitung Thermocet Flat Fire M (Seite 12 von 30) (Englisch)

607255

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

Page.12

SYMPTOM ACTION TO BE TAKEN

The pilot flame does not burn after

repeated pressing on the ignition

button.

1. If you are switching the unit on for the first time or after a service, there is air in

the pipes. It will take a little while until all the air has flowed out of the pipes and

gas which can be ignited comes through. Take it away and try to switch on the pi-

lot several times in order to allow the air to escape.

2. See whether the gas pipe to the apparatus is open and that there is sufficient gas

pressure to the apparatus.

3. Check whether there are sparks between the spark electrode and the pilot. If there

are no sparks:

a) Check whether the connection between the electrode and the ignition is broken

or faulty.

b) Check whether the spark short circuits at another point or jumps.

c) Check whether the ignition is broken.

d) Check whether the electrode is broken.

4. Take the glass away and try to light the pilot with a match.

a) If air blows onto the match flame, start to repeat the process until the air

inthe pipe has escaped.

b) If no air or gas comes from the pilot pipe, then this is probably blocked

or the gas valve is perhaps broken.

The pilot flame does not continue to

burn following ignition.

1. Check whether the pilot flame is large enough to burn round the thermo-

couple. If the flame is too small you must check the gas feed pressure. If

the pressure is good you must adjust the height of the pilot flame on the gas

valve of the apparatus. If the height of the pilot flame cannot be adjusted,

there may be an obstruction in the pilot.

2. Check whether the thermocouple is connected to the gas valve properly.

The main burner goes out when the

apparatus is warm.

1. This can be a normal effect of the thermostat

2. Check whether the pilot flame can heat the thermocouple sufficiently.

3. If the pilot flame is too small then the gas pipe or the pilot flame adjustment must

be checked.

Soot deposits on the glass door. 1. Check whether the lava stones are well placed in the unit.

Always keep the pilot burner free of burner filling.

2. Check whether there is any blockage in the burner openings

3. Check that the flue gas outlet is functioning correctly and that nothing is blocking

or obstructing it.

5. Check the pre-pressure

Sharp blue flames which are re-

leased by the burner or a pilot which

burns too wildly.

1. Check whether the restriction plate is used. Weak (stifling) pilot flame.

2. Check pilot flame burner pressure or flue layout See page 16

1. Check whether button A2 turns and that the batteries are ok.

2 Possible defect of gasblock.

3 Check whether the pilot flame ignites the burner well.

4. Check that the burner opening is not blocked.

Main burner will not burn after the

pilot burner burns.

9. Problems and possible solutions

Please check first of all whether all guidelines were followed before attempting to solve any problems with the

stove.

WARNING:

Solving problems with your unit, whether gas related or electrical must always be carried out by a qualified

technician

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thermocet Flat Fire M Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info