Bedienungsanleitung Thermocet Transparente 100 (Seite 17 von 36) (Englisch)

607231

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Pag.17

9. OPERATING INSTRUCTIONS FOR THE DUNGS AB COMBINATION

GAS REGULATOR

This regulator is fitted with a complete infra-red control system. This means that you can ignite the unit, smoothly

adjust the flame height and extinguish the unit using the remote control.

9.1 Infra-red remote control and its operation

The infra-red remote control allows you to comfortably control

the AB system. When in direct line of sight with the infra-red

receiver, the remote control has a range of approximately 15m

To start the system, press the buttons “ON” and “OFF” together

for at least 3 seconds. The start-up process is indicated by a se-

ries of three short tones. After the flame has lit, it can be in-

creased to the maximum height by pressing the “UP” button.

Pressing the “DOWN” button reduces the flame to its minimum

height. Pressing the “OFF” button for at least one second

switches off the system and places the unit in “Stand By" mode.

In the event of a fault in the unit (a red LED lamp lights on the

receiver), the system can be reset by pressing the “ON” and “OFF” buttons at the same time for at least 3 seconds

which will return it to the “STAND BY” mode. The “Automod” button starts automated adjustment of the system.

When automated adjustment is selected, the power of the unit automatically reduces from approximately 80% to

20% and then increase from 20% back to 80% again within a set time interval. This function can be stopped by

pressing the “Automod” button again or by pressing the “UP” or “DOWN” buttons. Depending on the individual

specification of the unit, the FOCContact knob can be used. Pressing the button engages a transistor that enables

external units with their own power supply to be switched on or off.

9.2 Igniting the gas fire.

Open the gas shut-off tap that has been fitted in the gas pipe leading to the unit. Now follow the steps described

above in “Infra-red remote control and its operation.”

Systeem "OFF"

AUTO mod / Aan / Uit

FOCContact / Aan / Uit

Led

Vlamhoogte / "UP"

Vlamhoogte / "DOWN"

Systeem "ON"

9.3 Basic system components (See page 22)

1: Modu box 4: Gas control block

2: Transformer (24 V) 5: Remote control

3: IR receiver 6: Wire harness

9.4 Connection to the gas regulation block wiring

1: Blue / Blue

2: Black / Black

3: Red / Red

4: Yellow-green

9.5 Adjusting the Gas regulation block (See adjustment values

on pages 23 and 24)

Setting the flow rate - Low setting

A Connect manometer to pressure measuring point (9)

B Ignite the fire

C Set the flow rate by turning adjustment screw 11 with a screw

driver.

- turn clockwise, to reduce "-"

- turn anti-clockwise, to increase "+"

Setting the flow rate - High setting

A Connect manometer to pressure measuring point (9)

B Ignite the fire

D Set the flow rate by turning adjustment screw 12 with a screw

driver.

- turn clockwise, to reduce "-"

- turn anti-clockwise, to increase "+"

1 2 3

mBar

- +

1 2 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thermocet Transparente 100 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thermocet Transparente 100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info