Bedienungsanleitung Thermocet Transparente 140 (Seite 18 von 36) (Englisch)

607233

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Pag.18

After completing any work: Test for leaks and check operation.

9.6 Connecting to the mains supply

The regulation equipment is fitted with an electronic control. Take into account the length of the cable

when connecting to a power socket.

9.7 Chimney

If it is connected to a chimney that had previously been connected to a wood-fuelled fire, than the flue

should be thoroughly and professionally cleaned as dirt can still become dislodged from the chimney when

used with gas. The chimney will need to be cleaned again after a couple of months.

9.8 Warning.

* Only install the unit in a well-ventilated room.

* The gas unit is only suitable for installation in a non-flammable, fire resistant mounting.

* This is an open fire so you should not place any light flammable articles nearby: care should be taken with ny

lon clothing.

* The exhaust gas outlet should have a minimum diameter that corresponds to the size of the connection.

* Protect all pipes (electric/gas) through a wall duct using a pvc tube and so forth.

* If there is a valve or slider in the exhaust gas outlet that allows the outlet to be fully or partially closed, this

should be locked in an open position using a protector connected to the control.

10. ELECTRICAL AND GAS CONNECTION

10.1 Electrical connection.

The regulator is composed of various components which should be fitted in the

correct manner. You need to provide the following:

* 230 V AC, 50 Hz power supply positioned near to the gas block fire.

* The plug and the power socket should be within reach at all times. Position the main components, namely the

control cabinet and the gas regulator combination in a place that is easily accessed. The maximum permitted

ambient temperature for all of these components is 60° C. The regulation box is simple to mount, for instance

on a wall. Remove the cover plate from the regulation box by unscrewing the 2 cover plate screws. The regu

lation box can be positioned on the assembly slots in the bottom of the regulation box.

10.2 Order of installation: electrical connections.

* Connect according to local regulations.

* Determine the position for the control box and the gas regulation combination (pay attention to the maximum

length of the wire harness).

* Check that the wire harness from the gas block is connected to the Modu box.

* The ignition cable should be passed through separately on its own. (excess sparking)

* Determine the position of the infra-red receiver (the lens should remain visible to the remote control)

* Insert the power cable into the wall socket.

* If used, connect the open position protector or GTP as shown in the wiring diagram. (See page 21).

* Ensure that the ground wire is properly connected. Without this connection, ionization current protection is

not possible.

* For connections and attachments for the basic gas regulation combination (See page 22).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thermocet Transparente 140 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thermocet Transparente 140

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info