Bedienungsanleitung Thermocet Trimline 120 DB Tunnel - 1138 (Seite 7 von 125) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Spanisch)

659030

Zoom out

Zoom in

Vorherige Seite

1/125

Nächste Seite

Page.6

Note: when installing the log and Pebble set and the various glowing materials and accessories, the fol-

lowing must be taken into account:

A: No glowing material in or on the pilot burner.

B: Prevent that ceramic material falls on the glass seals. Remove this if necessary. The window can be damaged.

Slot /opening between burner and mesh deco plate must be kept free of glowing material. Too

much placed glowing material can affect the combustion process.

Before placing the log set when heating on G25 20-25mBar (I2L / I2ELL) the premix brackets underneath

the double burner needs to be changed. (see APPENDIX 5 image 8)

4. PLACEMENT OF THE CERAMIC LOG AND OPTIONAL PEBBLE SET

Method:

* Loosen the screws holding the bottom and top glass holders (see APPENDIX 5).

* Place the suction cup(s) in the middle of the glass-panel and remove the panel by GENTLY

moving this first upwards and then the lower edge of the glass-panel very carefully and slowly

pulling toward you. Then place in a safe place where the window can not be broken or damaged.

If the removed glass panel is damaged (scratched and / or damaged edges) then no longer use the

glass panel and contact your dealer.

* Remove the deco plate and double burner out of the burning chamber.

* Unscrew both premix brackets from the burner.

* (1135/1136/1139/1149) Place the premix bracket for (G25) G20-25 met 2X Ø4 mm.

* (1137/1138/1048) Place the premix bracket for (G25) G20-25 met 2X Ø4,5 mm.

* Place screws back in place.

* The burner pressure and the injector need not be changed. Replace the Burner and the decorative plate.

4.1 Fitting the Ceramic log set (see APPENDIX7)

* Mix the glowing material (lava granules) and spread them evenly over the burner and the burner

plate so that they are just covered. Glowing embers can be placed here and there as decoration.

* Place the ceramic wood blocks in the correct order as shown on APPENDIX 7.

* Place the logs carefully. Other location can seriously affect the flames or malfunction of the

burn process (sooting)

* Before replacing the windows make sure if there must be a restriction plate to be placed or not.

See chapter 8 "Concentric chimney lay out"

* If there is a restriction required for your situation, remove the baffle plate by unscrewing it

from the front of the plate and move the plate backwards and then out. Now install the restriction

plate with two screws and replace the baffle plate. (Also see APPENDIX 5-7).

* Now place the window in reverse order as described at chapter “PLACING THE APPLIANCE” 2.2 and

on APPENDIX 5.

4.2 Fitting the optional Pebble set. (see APPENDIX8)

* Scatter vermiculite evenly over the burner tray. Make sure the pilot light remains unobstructed.

* Place a row of medium-sized and large pebbles at the front of the burner plate

* Fill the burner tray with small and medium-sized pebbles from the front to the rear.

Place the pebbles as closely as possible to each other on the burner tray.

* Fill the rear of the burner plate with medium-sized and large pebbles.

* Before replacing the window make sure if there must be a restriction plate to be placed or not.

See chapter 8 "Concentric chimney lay out"

* If there is a restriction required for your situation, remove the baffle plate by unscrewing it

from the front of the plate and move the plate backwards and then out. Now install the restriction

plate with two screws and replace the baffle plate. (Also see APPENDIX 5-7).

* Now place the window in reverse order as described at chapter “PLACING THE APPLIANCE” 2.2 and

on APPENDIX 5.

2.6 Fitting the Carrara / Basalt stones (see APPENDIX 8)

* Scatter vermiculite evenly over the burner tray. Make sure the pilot light remains unobstructed.

* Fill the burner tray and burner plate neatly and evenly with the Carrara stones.

* Reinstall the window, following the instructions for removing it in reverse order.

* Before replacing the window make sure if there must be a restriction plate to be placed or not.

See chapter 6 "Concentric chimney lay out"

* If there is a restriction required for your situation, remove the baffle plate (see APPENDIX 5)

by unscrewing it from the front of the plate after the plate backwards and then out.

Now install the restrictor plate with two screws and replace the baffle plate.

* Now place the window in reverse order as described at 2.2 on APPENDIX 5.

MAKE SURE THE PILOT LIGHT REMAINS UNOBSTRUCTED FROM ANY MATERIAL!

NOTICE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thermocet Trimline 120 DB Tunnel - 1138 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thermocet Trimline 120 DB Tunnel - 1138

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info