Bedienungsanleitung Thermocet Trimline 63 (Seite 15 von 54) (Englisch)

532677

Zoom out

Zoom in

Vorherige Seite

1/54

Nächste Seite

Page.15

8. Instructions for the Mertik Maxitrol GV60 and the Remote Control:

Ensure that the fuel supplied to the unit is clean and free from particles and moisture.

Before a gas supply pipe (new or existing) is connected to the main gas pipe at the gas meter and to the gas

control block of the unit, clean and dry compressed air should been blown through it.

Cut copper pipes as well as aluminium pilot pipes must be deburred and blown clean before they are con

nected. The dust filter at the connection to the gas control block will only filter out the coarsest dirt from

the system. Fine particles are still able to reach the inside and may damage and/or adversely affect regula-

tion in the gas control block.

Heat, moisture and dust are a threat to all electronic components

Protect the electronic gas control until all construction, plastering and paintwork has been completed. If

such work cannot be avoided, then protect the control against dirt and moisture penetration by using, for

example, plastic film.

Warning

Electronic components will become permanently faulty when exposed to temperatures higher than 60°C.

Standard AA batteries will crack open at temperatures >54°C and the battery contents will damage the

electronic switches located underneath. Batteries last longest at <25°C. At >50°C the life span is around 23

weeks, this makes the use of the gas fire unnecessarily expensive.

Only install the gas control block and receiver as pre-installed at the factory

Remember that components may have to be replaced or that repairs may have to be performed at a later

date. This may be more difficult if the control is installed using a method that is different from the instruc-

tions provided here.

Please note:

Only place the batteries after wiring to the receiver, gas control block and pilot set is connected.

Premature connection to the energy source may damage the control’s CPU (central processor).

Ensure that the ignition cable is not near the antenna wire and that they do not cross each other.

The high voltage released at ignition may damage the sensitive receiver circuit.

This may mean that the unit becomes less responsive or not responsive at all to handset commands. (See

photograph 1 on page 16)

Loosen the antenna wire from the terminals on the receiver box

Direct the antenna wire away from the ignition cable and in the direction of the control box door.

Ensure there is no contact with metal components. Ensure there is no damage to the connection to elec-

tronic components or to the wire itself. (See photograph 1 on page 16)

Connect the wires correctly to the contact breaker behind the gas control block.

The shortest wire runs immediately back to the 1/0 switch and can be found nearest to the back of the gas

control block. The longest wire runs to one of the two connections on the receiver box and only fits on one

of the screws.

Do not tighten the contact breaker and the thermocouple connection too tightly on the gas control

block or to each other.

It is sufficient to tighten by hand and add a half a turn with an open-end spanner. Tightening too much

will break the connection to the magnetic coil below and/or the insulation around the aluminium contact

pin in the contact breaker. This may lead to the magnetic coil not opening the gas supply to the pilot and

the unit not working.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thermocet Trimline 63 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thermocet Trimline 63

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info